Description
If you run a Wilson Combat Whisper suppressor setup and need your Rapid Thread or Flat Back attachment sitting exactly where it should, this shim kit is the piece that gets you there. Shims are thin, even-thickness rings of metal that stack behind a muzzle device so it lands at top dead center when you torque it down. Unlike a crush washer that squishes unevenly and can throw your alignment off, a proper shim keeps the device concentric to the bore, which matters a lot once you thread a can onto the end of it.
What the Wilson Combat 1/2×28 Shim Kit Is Built For
This particular kit is cut for 1/2×28 thread pitch, the standard on most .22 caliber and 5.56 barrels. It's a direct replacement for the shims that ship with Wilson Combat Rapid Thread and Flat Back interfaces, so you're not adapting a generic set to fit. The precision grinding is the whole point here. When you're stacking suppressor mount hardware, even a few thousandths of an inch of slop can lead to baffle strikes down the line, so the tighter the tolerance, the better you sleep at night.
Getting Your Wilson Combat Mount Timed Right
Installation is about as simple as it gets. Thread your mount on hand-tight, note how far off top dead center it sits, then add or swap shims until it stops just shy of 12 o'clock so it rotates into place as you torque it. Most folks land it around the 10 to 11 o'clock mark before the final tightening. If you're running this on a suppressor host, a heat-resistant thread locker is worth using once you've confirmed the timing is perfect.
Bottom line, this is a small part that punches above its weight. Keeping a spare set of the correct Wilson Combat shims on the bench means you're never stuck mid-install hunting for the right thickness. It's the kind of thing you don't think about until you need it, and then you're glad it's in the drawer.
Key Specifications
- Manufacturer: Wilson Combat
- Manufacturer Part Number: SP-RTMB-SHIMKIT2
- UPC: 810025500412
- Thread Pitch: 1/2×28
- Caliber Application: .22 / 5.56 muzzle threads
- Compatibility: Wilson Combat Rapid Thread & Flat Back attachments
- Designed Interface: Whisper Suppressor
- Fits Models: SP-RTMB and SP-RTMBFB-30
- Color: Silver
- Product Type: Accessory / Parts
What’s Included
- Wilson Combat 1/2×28 precision ground shim kit (assorted thicknesses)
Frequently Asked Questions
What does the Wilson Combat Shim Kit actually do?
The shims stack behind your muzzle device or suppressor mount so it ends up perfectly oriented, or timed, once you torque it down. Because they're an even thickness, they keep the device true and concentric to the bore. That alignment is important for consistent performance and matters even more when you're running a suppressor on the front end.
Will this kit fit my Wilson Combat Rapid Thread or Flat Back mount?
Yes, this set is made specifically for Wilson Combat Rapid Thread and Flat Back attachments cut for 1/2×28 threads. It's designed as a direct replacement for the shims that come with those interfaces, including the SP-RTMB and SP-RTMBFB-30. Just confirm your barrel and mount are 1/2×28 pitch before ordering.
Are shims better than a crush washer for a suppressor setup?
For suppressor use, shims are the way to go. A crush washer doesn't always compress evenly, which can leave your muzzle device slightly off-axis. That misalignment gets magnified over the length of a can and can lead to baffle strikes, so precision shims like these are the smarter choice.
Do I need any special tools to install the shims?
Nothing exotic. A vise with a barrel or upper receiver block and a torque wrench cover the job. Thread the mount on hand-tight, add shims until it stops just shy of 12 o'clock, then torque it into final position, and use a heat-resistant thread locker if it's serving as a suppressor mount.





Reviews
There are no reviews yet.