Description
Metric barrel threads used to mean hunting down oddball adapters, but SilencerCo made it easy with the Bravo Direct Thread Mount in M18x1. This little insert threads into any Bravo-pattern suppressor, including the Omega 300, Hybrid 46, Scythe-Ti, Harvester Evo, and other cans built on the common 1.375×24 HUB standard, and lets you spin it straight onto an M18x1 muzzle. That thread pitch shows up on plenty of European hunting rifles, so if you brought home a Sauer, Blaser, or similar rifle with metric threads, this is the piece that gets your can on it without a stack of adapters.
Why the Bravo Direct Thread Mount Runs Shorter
Compared to SilencerCo's ASR quick-detach setup, this direct thread mount shaves about 3/4 inch off the overall length of your suppressor. That may not sound like much on paper, but on a hunting rifle that already wears a 22 or 24 inch barrel, every bit of length you can trim makes the gun handier in a blind or on a sling. Direct thread also keeps things dead simple: fewer parts, less weight out on the muzzle, and a consistent mount that holds zero shot after shot. It is built from stainless steel with a black oxide finish, so it shrugs off heat and carbon like the suppressor it lives in.
Setting Up the M18x1 Bravo Mount
Installation is about as easy as it gets. Pull the existing mount or ASR module from the back of your Bravo-compatible can, thread this insert in, and snug it down. From there the suppressor threads directly onto your barrel like any other direct thread can. Keep in mind this mount is meant for fixed-barrel hosts like bolt guns, rifles, and pistol caliber carbines, which covers exactly the kind of platforms wearing M18x1 threads anyway. If you swap suppressors between several rifles with different thread pitches, picking up a few of these inserts in the pitches you need is a whole lot cheaper than buying another can.
Key Specifications
- Manufacturer: SilencerCo
- Manufacturer Part Number: AC690
- UPC: 817272011579
- Thread Pitch: M18x1
- Mount Pattern: Bravo (1.375×24 HUB)
- Material: Stainless Steel
- Finish: Black Oxide
- Length Reduction vs ASR Mount: Approx. 3/4 inch
- Suppressor Compatibility: Omega 300, Hybrid 46, Scythe-Ti, Harvester Evo, other Bravo/HUB suppressors
- Host Type: Fixed-barrel firearms (rifles, PCCs, subguns)
- Shipping Weight: 0.15 lb
- Product Type: Suppressor Mount / Direct Thread Insert
What’s Included
- Bravo Direct Thread Mount, M18x1 (AC690)
Frequently Asked Questions
Which suppressors does the Bravo Direct Thread Mount M18x1 fit?
It fits SilencerCo suppressors that use the Bravo mounting pattern, including the Omega 300, Hybrid 46, Scythe-Ti, and Harvester Evo. Since the Bravo pattern shares the common 1.375×24 HUB thread, it also works with many other HUB-compatible suppressors from various manufacturers. Just make sure your can accepts 1.375×24 rear modules before ordering.
What guns use M18x1 barrel threads?
M18x1 is a metric thread pitch found mostly on European hunting rifles from makers like Sauer, Blaser, Merkel, and similar brands. If you own an imported bolt gun with metric muzzle threads, there is a good chance it is M18x1, but always verify your barrel's thread pitch before buying. A quick check with calipers or a thread gauge saves headaches.
How much shorter is this than running the ASR mount?
Swapping from the ASR quick-detach system to this direct thread mount trims roughly 3/4 inch off the suppressor's overall length. It also drops a bit of weight off the muzzle end since you are not carrying the QD hardware. For hunting rifles where balance and handiness matter, that trade is worth it for a lot of folks.
Can I use the Bravo Direct Thread Mount on a pistol with a tilting barrel?
No, this mount is designed for fixed, non-moving barrels like those on bolt-action rifles, semi-auto rifles, and pistol caliber carbines. Tilting-barrel handguns need a piston or booster assembly to cycle reliably with a suppressor attached. Stick to fixed-barrel hosts and this mount will serve you well.




Reviews
There are no reviews yet.