Description
Serious 6.5 PRC handloaders reach for the Redding Type S Match Bushing Full Length Die Set when they want factory-grade consistency off their own bench. This two-die set brings together a Type S bushing full-length sizing die and Redding's Competition seating die, so you get precise neck tension control and dead-straight bullet seating from the same box. It's the setup a lot of precision and long-range folks run once they get tired of chasing runout and inconsistent velocities.
What the Type S Bushing Full Length Sizer Does
The full-length sizing die resizes the entire case body and sets the shoulder back while an interchangeable bushing handles the neck. Because the bushing self-centers on the case neck, concentricity stays tight and your loaded rounds chamber smooth every time. Bushings come in .001 inch increments, so you can tune neck tension exactly to your brass and the amount of grip you prefer. For 6.5 PRC, folks commonly land in the .288 to .292 range depending on brass brand and neck wall thickness, with ADG and Hornady cases often calling for slightly different numbers. The adjustable decapping rod lets you position the bushing to size only part of the neck when you want to, and pulling the bushing and internals turns it into a body die if you ever need one.
The Competition Seating Die in This 6.5 PRC Set
The other half of the set is Redding's Competition seating die, widely regarded as one of the best straight-line bullet seaters made. The seating stem is ground to match bullet profile for excellent case and bullet alignment, and the micrometer top adjusts seating depth in .001 inch clicks so you can repeat a load or tweak jump without guesswork. The sliding sleeve supports the case and bullet in alignment before the bullet ever starts into the neck.
Fitting Out Your Type S Match Set
Keep in mind the neck sizing bushing and shellholder are sold separately, which is standard for the Type S line since every reloader wants a different bushing for their brass. The set uses the industry-standard 7/8-14 thread, so it drops right into any standard press, and the 6.5 PRC uses a #6 shellholder. Grab the right bushing for your cases and you're ready to build match ammo.
Key Specifications
- Caliber: 6.5 PRC
- Die Type: Type S Match Bushing Full Length (2-Die Set)
- Dies Included: Type S Bushing Full Length Sizing Die + Competition Seating Die
- Neck Sizing: Interchangeable bushings in .001 inch increments
- Seating Adjustment: Micrometer, .001 inch increments
- Thread: 7/8-14 standard
- Shellholder: #6 (sold separately)
- Bullet Diameter: 0.264 inch
- Manufacturer: Redding
- Manufacturer Part Number: 36487
- UPC: 611760364877
- Shipping Weight: 1.39 lbs
What’s Included
- Type S Bushing Full Length Sizing Die
- Competition Micrometer Seating Die
- Standard size button and decapping pin retainer
- Hex wrench
- Hard plastic die storage box
Frequently Asked Questions
Does the Redding Type S 6.5 PRC die set come with a bushing?
No, neck sizing bushings are sold separately, which is standard across the entire Type S line. That way you can pick the exact bushing size that matches your brass and the neck tension you want. Redding offers them in .001 inch increments, and for 6.5 PRC most reloaders end up somewhere in the .288 to .292 range depending on brass and neck wall thickness.
What bushing size should I use for 6.5 PRC?
The right bushing depends on your brass and desired neck tension, so measure the neck diameter of a loaded round and subtract the grip you want. A common approach is to subtract about .002 to .003 inch from your loaded neck measurement. Many 6.5 PRC loaders report using a .288 to .291 bushing with Hornady or ADG brass, but it's worth measuring your own cases and grabbing two or three sizes to dial it in.
Do I need a shellholder with this set?
Yes, the shellholder is sold separately and the 6.5 PRC uses a #6 shellholder. It's a common size you likely already have if you load other cartridges in that case head family. Just make sure you have one on hand before your first sizing session.
Can the full length sizing die be used as a body die?
Yes. By removing the bushing and the internal decapping and expander parts, the Type S full length die can be run as a body die. That gives you some extra versatility if you want to bump the shoulder and size the body without touching the neck.





Reviews
There are no reviews yet.