Description
Q teamed up with Reptilia to build a mount that skips the whole rail-and-rings routine on The Fix. The AUS Direct Mount interfaces right to the receiver of The Fix and Mini Fix, which means no M1913 rail, no extra hardware, and no wasted height. The result is one of the cleanest ways to glass up your rifle without piling on parts or throwing off the balance. This version is cut for 34mm scope tubes and wears a matte black MIL-STD Type III, Class 2 hard anodized finish.
Why the AUS Direct Mount Fits The Fix So Well
Because it mounts flush to the receiver, this setup sits low and stays out of the way. It's machined from a single billet of 7075-T6 aluminum, which is the same tough alloy you'll find on serious precision hardware, and it tips the scale right around 5.3 ounces. Height over bore comes in at 2.6575 inches, giving you a natural cheek weld and repeatable zero retention trip after trip. The anti-snag profile keeps things smooth whether the rifle is slung, cased, or moving through brush.
Setting Up the 100-322 Mount
Installation is straightforward. The mount body clamps down with cross bolts torqued to 45 in-lbs, and the ring caps get snugged in an X pattern to 15 in-lbs, though it's always worth checking your scope maker's spec. Thread locker isn't required, but a dab of purple Loctite 222 is fine if you want the extra peace of mind. A T25 Torx or large flat blade handles the clamps and a T15 Torx takes care of the rings.
Room to Grow With ROF Accessories
One of the nicer touches here is that the AUS plays well with Reptilia's 34mm ROF mounts. That opens the door to adding an offset red dot at 45 or 90 degrees down the road by swapping a ring cap, so your setup can evolve as your needs do. Made in the USA and backed by a lifetime warranty against manufacturer defects, this is a buy-it-once piece of kit.
Key Specifications
- Manufacturer: Q LLC
- Manufacturer Part Number: 100-322
- Model: The Fix
- UPC: 850053448799
- Optic Diameter: 34mm
- Platform Compatibility: The Fix and Mini Fix
- Mount Type: AUS Direct-to-Receiver
- Material: 7075-T6 Aluminum (single billet)
- Finish: MIL-STD Type III, Class 2 Hard Anodize, Black
- Height: 39mm (1.54 in)
- Height Over Bore: 2.6575 in
- Weight: 5.3 oz
- Accessory Compatibility: Reptilia 34mm ROF Mounts
- Origin: Made in USA
- Warranty: Lifetime against manufacturer defects
What’s Included
- AUS Direct Mount (34mm, Black)
- Ring caps with T15 Torx screws
- Cross bolts with spring-loaded locking clamps
Frequently Asked Questions
What rifles does the 100-322 AUS Direct Mount fit?
It's built specifically for Q's The Fix and Mini Fix rifles. The mount interfaces directly with the receiver, so you don't need an M1913 Picatinny rail or any extra adapters. This is the black, 34mm tube diameter version.
Can I add a red dot to the AUS Direct Mount?
Yes. This mount is compatible with all of Reptilia's 34mm ROF mounts, which let you run an offset miniature red dot at a 45 or 90 degree position. You simply swap out a ring cap for the ROF unit using the existing T15 Torx screws.
What are the torque specs for installing this mount?
The clamp cross bolts get torqued to 45 in-lbs and the ring cap screws to 15 in-lbs, tightened in an X pattern. Always double-check your scope manufacturer's ring torque recommendation, since it can vary by brand. Thread locker isn't required, though a small amount of purple Loctite 222 is acceptable.
What is the mount made of and where is it built?
It's machined from a single block of 7075-T6 aluminum and finished with a MIL-STD Type III, Class 2 hard anodize for corrosion and wear resistance. It's made in the USA and carries a lifetime warranty against manufacturer defects. Total weight is about 5.3 ounces.




Reviews
There are no reviews yet.