Description
The Magpul Hunter 700 takes a classic Remington 700 short action and turns it into something that fits you instead of the other way around. It's a true drop-in stock, so your barreled action settles into a Type III hard anodized cast aluminum V-bedding block with no bedding compound or inletting needed. That aluminum block runs from the recoil lug back to the tang, which gives the action a stable, repeatable home and lets the barrel free float the way it should. Folks who have swapped one in off a factory Hogue overmold stock report the whole job taking around fifteen minutes with basic tools.
What Sets the Hunter 700 Apart
Where a lot of budget replacement stocks flex in the forend, the Hunter 700 uses a reinforced polymer shell that stays surprisingly stiff. Shooters running it prone and off a bench have kept groups tight, in some cases matching what they saw from far pricier fixed stocks. The barrel channel accepts every factory Remington barrel, including the VTR triangular contour, and clears aftermarket profiles up to a Medium Palma (0.920 inch diameter, measured 5.50 inches forward of the breech). It also plays nice with most factory and aftermarket triggers.
Dialing In Your Fit
Length of pull adjusts from 13 to 15 inches using the included spacers, and the stock ships with a 0.25 inch cheek riser already installed to get you close to a proper cheek weld under an optic. If you're running taller rings or a big objective, optional 0.50 and 0.75 inch risers are available, along with a no-rise piece for a lower weld. The near-vertical grip and forend speed bump give you solid, consistent contact whether you're shooting off a bag or a barricade.
Room to Grow
The Hunter 700 works right away with standard Remington hinged floorplates. When you're ready for detachable magazines, it upgrades to AICS-spec short action mags (5.56×45 or 7.62×51 pattern) by adding the Magpul Bolt Action Magazine Well, no custom inletting involved. M-LOK slots along the forend sides and bottom take bipods, slings, lights, and more. Made in the USA, it fits right-hand receivers only.
Key Specifications
- Manufacturer: Magpul Industries
- Manufacturer Part Number: MAG495-ODG
- UPC: 840815100751
- Model: Hunter 700
- Color: O.D. Green
- Fit: Remington 700 Short Action, right-hand receivers only
- Action Type: Bolt Action
- Construction: Reinforced polymer shell with Type III hard anodized A380 cast aluminum V-bedding block
- Length of Pull Range: 13 to 15 inches (adjustable with spacers)
- Cheek Riser: 0.25 inch installed from factory (0.50 and 0.75 inch optional)
- Barrel Clearance: Up to Medium Palma, 0.920 inch diameter
- Weight: 3.0 lbs without action and bottom metal (two spacers installed)
- Forend Width (max): 2.3 inches
- Butt Width (max): 1.5 inches
- Accessory Mounting: M-LOK slots on forend sides and bottom
- Origin: Made in the USA
What’s Included
- Magpul Hunter 700 stock (OD Green)
- 0.25 inch cheek riser (pre-installed)
- Length of pull spacers
- Installation instructions
Frequently Asked Questions
Will the Magpul Hunter 700 fit my Remington 700 without gunsmithing?
Yes, it's designed as a true drop-in for standard Remington 700 short action rifles with factory hinged floorplates. The aluminum V-bedding block means no bedding compound or inletting is required, and most people finish the swap in about fifteen minutes with basic tools. Just keep in mind it fits right-hand receivers only.
Can I run detachable magazines with the Hunter 700 stock?
Out of the box it works with your standard Remington hinged floorplate. If you want AICS-spec detachable box magazines in either the 5.56×45 or 7.62×51 pattern, you add the Magpul Bolt Action Magazine Well, which drops in without any custom inletting. It's a common upgrade for folks building toward a more precision-oriented setup.
Does the Magpul Hunter 700 come with a cheek riser installed?
It ships with a 0.25 inch cheek riser already in place, which gets most people close to a good cheek weld under a scope. If you're running taller rings or a large objective, optional 0.50 and 0.75 inch risers are available separately, and there's a no-rise piece if you prefer a lower weld. Length of pull also adjusts from 13 to 15 inches using the included spacers.
What barrel profiles will fit in the Hunter 700 barrel channel?
The channel clears every factory Remington barrel, including the VTR triangular contour, and free floats it. On the aftermarket side it accepts profiles up to a Medium Palma, which is 0.920 inch diameter measured 5.50 inches forward of the breech. That covers most sporter and heavier barrels without any modification.



Reviews
There are no reviews yet.