Description
The Limbsaver Precision-Fit Classic Recoil Pad is a straight drop-in replacement made for Remington platforms, and it does the one job you want a recoil pad to do: take the sting out of the shot. Made from Limbsaver's NAVCOM rubber, it absorbs and dissipates the energy and vibration that would otherwise land on your shoulder, reducing felt recoil by up to 70 percent. That means fewer flinches, more comfortable range days, and steadier follow-up shots when it counts.
Why the Precision-Fit Beats a Generic Slip-On
Because this pad is molded to the specific contour of Remington stocks, it lines up flush like a factory piece instead of hanging off the back like a rubber boot. It's built to fit a wide range of models including the 700 SPS/ADL/BDL, 710, 770, 7600, 870, 1100, and 11-87 synthetic, along with a handful of other platforms like the SP-10 and certain Christensen Arms stocks. The pad adds 1 inch to your length of pull, which is worth noting if you're already dialed in on stock fit. The soft, tacky face also grips the shoulder pocket so the gun stays planted through the recoil cycle.
Getting the Recoil Pad Installed
This is about as easy as gun work gets. There's no grinding or shaping required since it comes pre-fit, so you just pull your old pad, save those two screws, and thread the new one on. Most folks have it done in under a minute. One tip from the field: hold onto the original screws, since the pad ships without hardware and relies on your factory screws to mount up.
Built for the Weather and the Recoil
The textured, no-slip surface and all-weather construction mean it holds up whether you're punching paper at the range or sitting in a wet duck blind. It shines with heavy loads, so if you're running 3-inch turkey loads, slugs, or a hard-kicking magnum rifle, this is where a Limbsaver earns its keep. Proudly made in the USA.
Key Specifications
- Manufacturer: Limbsaver
- Model: Classic Precision-Fit
- Manufacturer Part Number: 10101
- UPC: 697438101012
- Material: NAVCOM Rubber
- Color: Black
- Style: Pre-Fit
- Thickness: 1 inch
- Added Length of Pull: 1 inch
- Template Dimensions: 5 in x 1-5/8 in
- Felt Recoil Reduction: Up to 70%
- Fits: Remington 700/710/770/7600/870/1100/11-87 synthetic, SP-10
- Country of Origin: USA
What’s Included
- Limbsaver Classic Precision-Fit Recoil Pad (1 pad)
Frequently Asked Questions
Will this Limbsaver pad fit my Remington 870?
Yes, this pad is molded to fit the Remington 870 along with the 700 SPS/ADL/BDL, 710, 770, 7600, 1100, and 11-87 synthetic stocks, plus a few others like the SP-10. It's a pre-fit design, so it should line up flush on compatible synthetic stocks with no shaping needed. If you have an unusual or aftermarket stock, it's smart to compare your stock against the installation template before mounting.
Do I get mounting screws with the recoil pad?
No, the pad ships without hardware and uses your factory screws. When you pull your old pad, hang onto those two screws and use them to thread on the Limbsaver. It's a simple swap that most people finish in about a minute.
How much recoil does the Limbsaver Precision-Fit actually reduce?
Limbsaver rates the NAVCOM rubber at reducing felt recoil by up to 70 percent. It won't erase kick entirely, but it takes the sharp bite out, which really shows up with heavy magnum rifle loads and 3-inch shotgun shells. Many shooters find it saves them from developing a flinch during long sessions.
Does the pad change my length of pull?
Yes, this pad adds 1 inch to your length of pull. That's worth keeping in mind if your stock fit is already dialed in for you. For most shooters the extra length is a non-issue, but taller or shorter folks may want to factor it in.




Reviews
There are no reviews yet.