0
0

Lee Precision Micrometer Bullet Seating Die 6.5mm Creedmoor

UPC: 734307922238

$26.99

7 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

If you handload 6.5mm Creedmoor and you're chasing consistency, this is the die that lets you fine tune seating depth without the guesswork. The micrometer head reads just like a precision depth micrometer, with laser engraved divisions marked in thousandths of an inch. Adjustment is smooth with no clicks to count, so you can move the thimble, lock in your number, and know you'll land on the same seating depth batch after batch.

What Sets the Lee Micrometer Seating Die Apart

This die uses dead length seating, meaning the body contacts the shell holder to assure uniform seating depth every pull of the handle. The floating bullet guide holds the case mouth and bullet in alignment, and Lee's testing shows the sliding guide design produces cartridges with very low bullet runout. The seating stem is machined and burnished so it seats nearly any point style bullet, including polymer tips, boat tails, and hollow points, without leaving marks or damage on the nose.

Seating and Crimping in One Pass

One of the handier touches here is the convertible bullet guide. Unthread it and re-install it reversed, and the die will seat and crimp at the same time, which is an exclusive Lee feature. For folks loading 6.5 Creedmoor for an AR-10 or a magazine fed bolt gun where a little crimp helps, that flexibility is a nice thing to have in a single die.

Fitting the 6.5 Creedmoor Micrometer Die to Your Press

The die body uses the industry standard 7/8 inch by 14 thread, so it drops into just about any single stage, turret, or progressive press, including Lee, RCBS, Hornady, Lyman, and Dillon setups. Reloaders who've run these dies report loaded round runout in the .001 to .003 range with proper setup, which is right in line with dies that cost quite a bit more. For a 6.5 Creedmoor shooter trying to tighten groups without reinventing their bench, this is a straightforward upgrade.

Key Specifications

  • Manufacturer: Lee Precision
  • Manufacturer Part Number: 92223
  • UPC: 734307922238
  • Caliber: 6.5mm Creedmoor
  • Die Type: Micrometer Bullet Seating Die
  • Seating Style: Dead Length
  • Micrometer Divisions: 0.001 inch
  • Adjustment: Smooth, no clicks
  • Thread: 7/8 inch x 14 (industry standard)
  • Bullet Guide: Floating, reversible for seat and crimp
  • Body: Laser engraved one piece
  • Country of Origin: USA
  • Shipping Weight: 0.594 lb

What’s Included

  • Lee 6.5mm Creedmoor Micrometer Bullet Seating Die
  • Instructions

Frequently Asked Questions

Will the 6.5 Creedmoor micrometer seating die fit my press?

Yes. The die body uses the industry standard 7/8 inch by 14 thread, so it threads into virtually any modern single stage, turret, or progressive press, including Lee, RCBS, Hornady, Lyman, and Dillon. If your press uses a thicker toolhead, you can invert the Lee lock ring or use another brand's lock ring.

Can this die seat and crimp at the same time?

It can. The floating bullet guide is reversible, so you simply unthread it and re-install it to enable simultaneous seating and crimping. That said, many precision loaders prefer to seat and crimp in separate steps for the most consistent results, and you can run it that way too.

How precise are the micrometer adjustments?

The laser engraved thimble and body read in divisions of .001 inch, just like a precision depth micrometer, and the adjustment is smooth with no clicks. Reloaders running these dies commonly report loaded round runout in the .001 to .003 range when the die and press are set up properly.

Will the seating stem mark my bullets?

No. The seating stem is machined and burnished to seat nearly any point style bullet without marking or damaging the nose, including polymer tipped, boat tail, and hollow point designs. If you run an unusual bullet profile, Lee can make a custom stem to match it.

Additional information

UPC

734307922238

Manufacturer

Manufacturer Part Number

92223

Caliber/Gauge

6.5mm Creedmoor

Shipping Weight

0.594

Reviews

There are no reviews yet.

Be the first to review “Lee Precision Micrometer Bullet Seating Die 6.5mm Creedmoor”