Description
This is the .291 inch bushing from Hornady's Match Grade New Dimension lineup, a small piece of polished steel that has a big say in how your handloads shoot. It drops into the Hornady Match Grade neck size and full length dies and controls exactly how much the case neck gets squeezed down. Because it only sizes the outside of the neck to the diameter you pick, your brass gets worked less than it would with a traditional one-size die and expander ball setup, which means longer case life and more consistent neck tension round after round.
What the .291 Bushing Does Inside Your Die
The bushing sits inside the die body and floats, so it self-centers on the case neck as the brass is pushed up into it. That self-centering action is the whole point. It keeps everything concentric and eliminates the chance of oversizing and overworking the neck. Tight tolerances at the press tend to show up as tighter groups downrange, and that is exactly what this system is built to deliver for competition and precision loads.
Picking the Right Hornady Match Grade Bushing Size
Most reloaders find their bushing by seating a bullet in the brass they actually load, then measuring the outside diameter of the loaded neck with a caliper or micrometer. From there you subtract your desired neck tension, usually about .002 to .003 inch, and order the bushing closest to that number. Keep in mind brass springs back a touch after sizing, roughly .001 inch, so the final inside diameter ends up slightly larger than the bushing itself. The system works best with brass that has uniform neck wall thickness or has been neck turned, since bushings reference the outside of the neck.
Build Out Your Bushing Collection
Hornady offers these in close increments, so it is smart to keep a size above and below your target on hand for load development. The .291 sits right in the range commonly used for 6.5mm cartridges like the 6.5 Creedmoor, depending on your brass and bullet combination. Grab the one your loaded round measurements call for, and you can fine tune neck tension without waiting on a shipment every time you want to experiment.
Key Specifications
- Diameter: .291 in
- Bushing Type: Self-centering neck size bushing
- Compatibility: Hornady Match Grade New Dimension neck size and full length dies
- Material/Finish: Polished steel
- Outside Diameter: .750 in
- Quantity: 1
- Common Use: 6.5mm cartridges including 6.5 Creedmoor
- Manufacturer: Hornady
- Manufacturer Part Number: 594291
- UPC: 090255592917
- Shipping Weight: 0.03 lb
What’s Included
- One (1) Hornady Match Grade .291 neck size bushing
Frequently Asked Questions
What dies does the Hornady Match Grade .291 bushing work with?
This bushing is made for the Hornady Match Grade New Dimension neck size and full length dies. It drops right into the die body and self-centers on the case neck. The dies are sold separately, and the bushing is not included with them, so you select the size your cartridge needs.
How do I know if .291 is the right bushing size for me?
Seat a bullet in the brass you load, then measure the outside diameter of the loaded neck with a caliper or micrometer. Subtract your desired neck tension, commonly about .002 to .003 inch, and order the bushing closest to that number. Remember that brass springs back around .001 inch after sizing, so the finished inside diameter ends up a hair larger than the bushing itself.
Does the .291 bushing reduce how much my brass gets worked?
Yes. Since the bushing only sizes the outside of the neck to the exact diameter you choose, it does not oversize the neck and then open it back up with an expander ball. That gentler process work-hardens the brass less, which helps with case longevity and more consistent neck tension over repeated firings.
Will this bushing work for 6.5 Creedmoor?
The .291 falls within the range often used for 6.5mm cartridges like the 6.5 Creedmoor, though the exact size depends on your brass and bullet. The best move is to measure a loaded round and confirm before ordering. Many reloaders keep a size above and below their target on hand for load development.





Reviews
There are no reviews yet.