Description
The Hornady Lock-N-Load AP Shell Plate #9 is the part that lets your progressive press handle the old Winchester pair, .38-40 WCF and .44-40 WCF. If you shoot cowboy action, feed a lever gun, or just love running the classic rimmed cartridges, this is the plate that carries those cases through each station on the press. It indexes to the drive hub, holds the case head at the correct position, and keeps everything moving so you can focus on cranking out rounds.
What the #9 Plate Covers
This one is sized specifically for .38-40 Winchester and .44-40 Winchester, which share the same case head dimensions. Because Hornady builds plates around head size rather than a single caliber, any cartridge with a matching rim and head can run on the #9 as well. If you're not sure where your round falls, Hornady's shell plate chart is the quick way to confirm before you buy.
Built for Smooth Feeding on the Lock-N-Load AP
Hornady's improved shell plates feature a subtle radius machined into each shell holder mouth, which makes a real difference when cases are indexing fast. The retainer spring groove is beveled so the spring stays put when you're dropping cases in, and that keeps the press running without stopping to fight a sprung retainer. It's the kind of small detail that matters once you're a few hundred rounds into a session. The plate is machined from steel and heat treated so it holds up over the long haul.
Swapping Plates and What It Fits
Changing calibers on the Lock-N-Load AP mostly comes down to swapping the shell plate, so keeping a few on hand for the cartridges you load makes caliber changes quick. Beyond the current AP press, the #9 also works on the older Hornady Pro-Jector and Projector presses, so folks running the earlier machines are covered too. A little general-purpose grease on the ball detents during install keeps the indexing crisp.
Key Specifications
- Shell Plate Number: #9
- Calibers: .38-40 Winchester (WCF) / .44-40 Winchester (WCF)
- Compatible Presses: Lock-N-Load AP, Pro-Jector, Projector
- Material: Heat-treated steel
- Manufacturer: Hornady
- Manufacturer Part Number: 392609
- UPC: 090255926095
- Matching Shell Holder: #9 (390549)
- Style: Press Type
- Shipping Weight: 0.55 lb
What’s Included
- One (1) Hornady Lock-N-Load AP #9 Shell Plate
Frequently Asked Questions
What calibers does the Hornady #9 shell plate fit?
The #9 plate is built for .38-40 Winchester (WCF) and .44-40 Winchester (WCF), which share the same case head dimensions. Hornady sizes its plates by head size, so any cartridge with a matching rim and head can run on it. If your cartridge isn't one of those two, check Hornady's shell plate chart to find the right number.
Will the #9 shell plate work on an older Hornady Projector or Pro-Jector press?
Yes. Along with the current Lock-N-Load AP progressive press, the #9 plate also fits the older Pro-Jector and Projector presses. If you're running one of the earlier machines, this is still the correct plate for .38-40 and .44-40.
Do I need the matching shell holder too, or just the plate?
For progressive loading on the Lock-N-Load AP, the shell plate is what carries your cases through the stations, so that's the part you need on the press. The separate #9 shell holder (part 390549) is used on single-stage presses and isn't required for AP progressive work. Many reloaders keep both around if they also run a single-stage setup.
What's the best way to install the #9 shell plate for smooth indexing?
Put a small amount of general-purpose grease on the ball detents underneath the plate and on the top of the sub-plate, then align it with the keyed drive hub and secure the retainer bolt. Stretch the case retainer spring around the plate last. That grease on the detents is what keeps the indexing crisp cycle after cycle.




Reviews
There are no reviews yet.