Description
The factory black ramp on a Ruger LCR is one of the most common gripes owners have. It practically disappears against a dark target or in low light, and that makes a compact defensive revolver harder to shoot well than it should be. The Hi-Viz LCR2010R fixes that with a bright red fiber optic LitePipe that catches ambient light and gives you a glowing dot to drive toward the target, so your eye lands on the front sight fast.
What Sets the LCR2010R Apart
Hi-Viz builds this sight on a steel base wrapped in their clear overmold design, which is what keeps the LitePipe protected through hard use and holstering. Two details make it stand out from a plain fiber optic swap. The LitePipe uses a square profile instead of the usual round one, which gives you a cleaner, more defined dot to line up in the rear notch. The base also comes pre-drilled for the retaining pin, so you are not stuck drilling your own hole the way you would be on some other Ruger sight upgrades.
Fitment for Your Ruger LCR or LCRx
This red version is made for the centerfire guns: Ruger LCR and LCRx chambered in .38 Special, .357 Magnum, and 9mm Luger. It does not fit the rimfire and .327 models, so steer clear if you are running an LCR in .22 LR, .22 Magnum, or .327 Federal. Double-check your chambering before ordering and you will be set.
Installing the LCR2010R at Home
Plenty of LCR owners handle this swap themselves in a few minutes. You tap out the factory roll pin, drop the new sight into the barrel slot, and reinstall the pin. The one thing to know going in is that the little roll pin can be stubborn, so use a proper roll pin punch, immobilize the revolver in a padded vise or on a cutting board, and a dab of blue thread locker on the pin helps keep everything put. If you would rather not fuss with it, any gunsmith can knock it out quickly. Either way, the payoff is a front sight you can pick up instantly.
Key Specifications
- Manufacturer: Hi-Viz
- Manufacturer Part Number: LCR2010R
- Model: CompSight
- UPC: 613485588088
- Product Type: Fiber Optic Front Sight
- LitePipe Color: Red
- LitePipe Profile: Square
- Base Material: Steel with clear overmold
- Fits: Ruger LCR and LCRx in .38 Special, .357 Magnum, 9mm Luger
- Does Not Fit: LCR .22 LR, .22 Magnum, .327 Federal
- Sight Length: 0.850 in
- Sight Width: 0.245 in
- Sight Height: 0.251 in
- Warranty: Limited lifetime (LitePipe considered a wear item)
What’s Included
- Hi-Viz LCR2010R red fiber optic front sight
- Retaining pin
Frequently Asked Questions
Will the LCR2010R fit my Ruger LCR?
It fits the centerfire Ruger LCR and LCRx models chambered in .38 Special, .357 Magnum, and 9mm Luger. It is not made for the rimfire or .327 versions, so it will not work on an LCR in .22 LR, .22 Magnum, or .327 Federal. Confirm your caliber before ordering and you are good to go.
Is the Hi-Viz LCR2010R hard to install myself?
Most owners handle it at home in just a few minutes. You tap out the factory roll pin, seat the new sight in the barrel slot, and reinstall the pin. The base is pre-drilled so no drilling is needed, but the small roll pin can be finicky, so use a proper roll pin punch, keep the revolver secured, and add a touch of blue thread locker to the pin. A gunsmith can also do it quickly if you would rather not.
How is the red LitePipe different from a standard fiber optic sight?
The LCR2010R uses a square profile LitePipe instead of the more common round one, which gives you a crisper, better-defined dot to center in the rear notch. It sits in a steel base with a clear overmold that shields the fiber from knocks and holster wear. That combination is what makes it hold up well over time.
Does the red or green LitePipe work better?
Both gather ambient light and pop against a target far better than the factory black ramp. Red tends to stand out nicely against green foliage and lighter backgrounds, while green reads a little brighter to some eyes in dim conditions. It comes down to personal preference, and plenty of LCR owners are happy with either color.





Reviews
There are no reviews yet.