Description
If you're chasing tighter groups out of your 357 Magnum or looking to tighten up accuracy loads in 38 Special, this is where a lot of reloaders stop fighting their old seating die. The Redding Competition Seater Die uses a spring-loaded, precision-fit seating stem that drops down into the die and aligns the bullet with the case mouth well before seating actually begins. That stem is ground to match bullet diameter so closely it can be shown to float on a column of air, which is a fancy way of saying runout and concentricity problems get solved before they ever start.
How the Competition Seater Die Tightens Up Your 357 and 38 Loads
The whole cartridge gets cradled in a close-fitting, precision-ground sleeve that supports both case and bullet before the press cams over. Instead of nudging a bullet in slightly crooked and hoping for the best, everything stays in line through the full stroke. For people loading for revolvers they care about, or shooting bullseye and silhouette matches, that consistency shows up on paper.
Dialing In Seating Depth With the Micrometer Head
The micrometer top is marked in .001" increments and adjusts without clicks, so you get infinite fine-tuning of overall length. It also has a zero-set feature, which means once you find the depth a particular bullet and load like, you can note the setting and come right back to it after switching bullets or pulling the die for cleaning. Swapping between light 38 wadcutters and heavier 357 loads becomes a quick job instead of a guessing game.
A Dedicated Seater Built for Separate Crimping
This is a no-compromise seater, which means it does not crimp. Serious revolver and competition loaders generally crimp as its own step anyway, and Redding builds a Profile Crimp and a Taper Crimp die for exactly that. The 7/8-14 threaded body is slightly extended for full lock ring engagement and has an oversize bellmouth chamfer at the bottom to feed cases smoothly on progressive presses. Machined and hand-finished in the USA, it runs with a standard #12 shellholder.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 55282
- UPC: 611760552823
- Caliber: 38 Special / 357 Magnum
- Die Type: Competition Bullet Seating Die
- Adjustment: Micrometer, .001" increments, infinitely adjustable with zero-set
- Seating Stem: Spring-loaded floating stem, precision ground to bullet diameter
- Crimping: None (separate crimp die required)
- Thread: 7/8-14
- Shellholder: #12 (sold separately)
- Press Compatibility: Single stage and progressive presses
- Country of Origin: Made in USA
What’s Included
- Redding Competition Seater Die (38 Special / 357 Magnum) with micrometer seating head
Frequently Asked Questions
Does the Redding Competition Seater Die crimp the bullet?
No, this is a dedicated seating die with no crimping capability by design. Redding builds it this way so you can seat and crimp as two separate steps, which produces more consistent ammo. If you want to crimp, you'll want to add a Redding Profile Crimp or Taper Crimp die.
Will this die work on a progressive press?
Yes. The 7/8-14 threaded body is slightly extended for full lock ring engagement, and the bottom has an oversize bellmouth chamfer with a smooth radius to help cases and bullets feed in cleanly. It runs just as well on a single stage if that's what you're using.
What shellholder do I need for 38 Special and 357 Magnum?
This caliber uses a standard #12 shellholder. The shellholder is not included with the die, so you'll need one to run your cases. Most reloaders loading 38/357 already have the #12 on hand.
What makes the Competition Seater Die more accurate than a standard seater?
The spring-loaded floating seating stem drops into the die and aligns the bullet with the case before seating starts, and the close-fitting sleeve supports the case and bullet through the whole stroke. That combination cuts down on runout and keeps bullets seated straight. The .001" micrometer head also lets you set and repeat your seating depth precisely.





Reviews
There are no reviews yet.