Description
The Lee Precision 45-70 Govt Quick Trim Die takes the most tedious part of reloading and turns it into a quick crank of the handle. This is the caliber-specific die that holds your .45-70 Government brass steady and square so the cutter trims every case to the exact same length, every single time. No measuring, no trial-and-error, no fussing with a caliper between pieces.
Keep in mind this is the trim die only. It's built to run with the Lee Deluxe Quick Trim Case Trimmer or the Lee Value Trim Case Trimmer, both sold separately. Once you've got one of those cutters, you just thread the die into your press, drop a case in, and go. The die body grips the brass with an internal o-ring so the case doesn't spin while you work, and the cutter squares the mouth while chamfering the inside and outside at the same time. That's three operations folded into one step, which is a big reason folks who switch to this system stop dreading case prep.
What Sets the 45-70 Quick Trim Die Apart
The die is made from steel and threaded a standard 7/8-14, so it fits any press that accepts common reloading dies. Because each die is cut for a specific cartridge, it keeps the trimmer in precise alignment with the case and holds a tight, repeatable length. Reloaders who run the Quick Trim system routinely report trimming right at spec with consistent results across a whole batch of brass.
Running the 45-70 Govt Quick Trim Die on Your Bench
The workflow is simple: resize and deprime your .45-70 brass first, then move it to the press holding the Quick Trim die and cutter. A few turns of the crank and the case is trimmed, chamfered, and ready to load. It pairs especially well with a turret or single-stage setup where you can keep a dedicated station going. If you shoot a lever gun or any .45-70 and load in volume, this die earns its keep fast.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number (MPN): 90458
- UPC: 734307904586
- Caliber: .45-70 Government
- Product Type: Quick Trim Die
- Material: Steel
- Thread: Standard 7/8"-14
- Function: Trims case to length and chamfers inside and outside of case mouth
- Compatibility: Lee Deluxe Quick Trim Case Trimmer (90437) or Value Trim Case Trimmer (90386)
- Length: 4.7 in
- Country of Origin: United States
What’s Included
- Lee 45-70 Govt Quick Trim Die (trim die only)
Frequently Asked Questions
Does the 45-70 Govt Quick Trim Die come with a cutter or trimmer?
No, this is the trim die only. You'll need the Lee Deluxe Quick Trim Case Trimmer (90437) or the Lee Value Trim Case Trimmer (90386), both sold separately, to do the actual trimming. The die holds and aligns your brass while the cutter does the work.
Does this die chamfer the case mouth too, or just trim?
When used with the Quick Trim cutter, the system trims the case to length and chamfers both the inside and outside of the case mouth in the same motion. That folds a couple of steps into one. Some reloaders still like to finish with a hand deburring tool for a lighter chamfer, but for most loading it leaves a clean, square mouth.
Do I need calipers to use the 45-70 Quick Trim Die?
No calipers or measuring are required. The die is cut specifically for .45-70 Government, so it keeps the cutter in precise alignment and trims to a consistent length automatically. The Deluxe trimmer also has a click-adjustable stop that lets you fine-tune length in .001 inch increments if you want to trim shorter than standard.
Will this die fit my reloading press?
Yes. It's threaded in the standard 7/8-14 size, so it fits any press that accepts common reloading dies, including Lee single-stage and turret presses. You just thread it in, drop in a resized and deprimed case, and start trimming.





Reviews
There are no reviews yet.