Description
Forster built its name on straight-line seater dies, and the Ultra Micrometer version is the top of that lineup. For 260 Remington handloaders chasing tight groups, this die takes the guesswork out of seating depth. A spring-loaded chamber sleeve fully captures the case before the bullet ever starts moving, so the case, bullet, and seating stem all stay locked in alignment through the entire stroke. That design supports the full outside diameter of the sized case rather than just the neck and rim, which is where a lot of runout comes from on lesser dies.
What the Micrometer Head Brings to the Bench
The micrometer top is the real draw here. Index marks are laid out in .001 inch increments with crisp white graduations that are easy to read, and you can make fine adjustments down to roughly .0005 inch in either direction. Once you've measured a seated round and know where you want to be, you simply dial the micrometer to the exact depth and the next cartridge comes out right where you expect. If you run several bullet styles through the same rifle, jot down the micrometer setting for each one and you can return to it later without re-doing the whole trial-and-error dance.
Built for the 260 Remington Precision Crowd
This is a non-crimping seater, so it's focused purely on accurate seating and consistent runout rather than locking the bullet in place. The seating stem has been refined over the years to handle a wide range of projectiles, including ballistic-tipped and most VLD-style bullets, so long 6.5mm match bullets like Bergers and ELD-X seat cleanly without leaving rings on the ogive. Each die is machined from quality steel to tight tolerances and hand polished before and after heat treating.
Fitting It Into Your Press
The Ultra Micrometer Seater threads into standard 7/8-14 reloading presses, and it ships with Forster's cross bolt locking ring that clamps the split ring rather than digging a set screw into the die threads. Handloaders who've run plenty of seater dies tend to call this one of the best straight-line setups they've used, and the micrometer makes load development on a 260 Remington a whole lot faster.
Key Specifications
- Manufacturer: Forster Products
- Cartridge: 260 Remington (6.5-08)
- Die Type: Ultra Micrometer Bullet Seating Die
- Crimp Style: Non-crimping
- Micrometer Adjustment: .001 inch increments, fine-tunable to .0005 inch
- Thread Size: 7/8-14
- Lock Ring: Forster cross bolt split locking ring
- Country of Origin: Made in the U.S.A.
- Manufacturer Part Number: U00056
- UPC: 757253007811
What’s Included
- One Forster Bench Rest Ultra Micrometer Seater Die
- One Forster cross bolt split-type lock ring
- Instructions
Frequently Asked Questions
How fine can you adjust seating depth on the Forster Ultra Micrometer Seater Die?
The micrometer head is marked in .001 inch increments, and you can fine-tune down to about .0005 inch in either direction. The white graduations are easy to read and record, so once you find a setting you can note it and return to it later. This takes most of the trial and error out of dialing in a load.
Does this 260 Remington die crimp the case?
No, this is a non-crimping seater die. It's designed for accuracy and consistent runout, holding the case, bullet, and seating stem in alignment through the whole seating stroke. If you want a crimp, you'd add a separate crimp die to your process.
Will the Ultra Micrometer Seater Die handle long VLD and match bullets?
Yes. Forster refined the seating stem over the years to fit a wide range of projectiles, including ballistic-tipped and most VLD-style bullets. Handloaders report it seats long 6.5mm match bullets like Bergers and ELD-X cleanly without leaving marks on the ogive.
What press does this die fit?
It uses the standard 7/8-14 thread, so it works in common single-stage and turret presses. It ships with Forster's cross bolt locking ring that clamps the split ring rather than driving a set screw into the die body.





Reviews
There are no reviews yet.