Description
If you load for a .45 caliber and you've ever felt a bullet drag going into a fired case neck, that's your sign the brass walls are running thick. The Forster 0.4545" Inside Neck Reamer is built to fix exactly that. It drops into the cutter head of your Forster Case Trimmer in place of the pilot and shaves the extra brass off the inside of the neck, bringing wall thickness back into line so your bullets seat with even tension round after round. This one is sized for .452 diameter bullets, ground .0025" to .003" over bullet diameter to the .4545" spec.
Thick case necks are more than a cosmetic issue. They can crowd the chamber, drive up pressure, and throw the occasional flyer that ruins an otherwise good group. Reaming the inside of the neck pulls that brass back out of the way and gives you a more uniform, predictable load. Forster grinds these from high grade, wear-resistant tool steel, and the staggered tooth layout is what keeps the cut smooth instead of chattering and gouging the brass.
Where the 0.4545" Neck Reamer Fits In
This reamer is made to run in the Forster Original, Classic, and Power Case Trimmers. It mounts right where the pilot normally sits in the cutter shaft. On the Power Case Trimmer, keep the drill press spindle at its lowest speed so the tool cuts clean and lasts. If you run the standard Forster trimmer setup, this slides into your workflow without any extra tooling.
Getting the Most From the .45 Caliber Inside Neck Reamer
Timing matters with neck reaming. Standard reamers like this are meant to be used after the case has been fired with a full load and before you neck size or full-length size. The easy field test is to slide a bullet into a fired, unsized case neck. If you feel interference, the neck is thick and reaming (or outside turning) is worth doing. Turn the reamer all the way through the neck, then keep turning as you back it out so the finish stays clean. A quick chamfer and deburr afterward and you're ready to size and seat.
Key Specifications
- Manufacturer: Forster Products
- Manufacturer Part Number: NR1452
- UPC: 757253005053
- Reamer Diameter: 0.4545"
- Bullet Diameter: .452"
- Caliber: .45 Caliber
- Material: High grade, wear-resistant tool steel
- Tooth Design: Staggered tooth
- Grind Spec: .0025" to .003" over bullet diameter
- Compatible Trimmers: Forster Original, Classic, and Power Case Trimmers
- Color: Silver
- Country of Origin: USA
- Quantity: 1
What’s Included
- One Forster 0.4545" Inside Neck Reamer (NR1452)
Frequently Asked Questions
What does the 0.4545" inside neck reamer do?
It removes excess brass from the inside walls of a case neck. Thick necks can raise chamber pressure and cause flyers, so reaming brings the wall thickness back to a consistent dimension. That gives you more uniform neck tension and more predictable loads.
Which trimmers does the Forster inside neck reamer fit?
It's designed to run in the Forster Original, Classic, and Power Case Trimmers. The reamer mounts in the cutter head in place of the pilot. If you're running the Power Case Trimmer, set the drill press to its lowest speed for a clean cut.
What bullet diameter is this .45 caliber reamer sized for?
This one is ground for .452 diameter bullets, which is where the .4545" reamer dimension comes from. Forster grinds standard neck reamers .0025" to .003" over the maximum bullet diameter. That slight oversize is what leaves room for sizing after reaming.
When should I ream the neck versus turn it?
A good rule of thumb is to ream after firing and turn after sizing. Standard reamers like this are meant to be used after a case has been fired with a full load and before neck or full-length sizing. To check if you need it, slide a bullet into a fired, unsized neck, and if you feel interference, it's time to ream or outside turn.





Reviews
There are no reviews yet.