Description
Reloading .38 Special and .357 Magnum is one of the most rewarding ways to feed a wheelgun, and this Redding Carbide 3-Die Set makes the whole job smoother from the first pull of the handle. The standout feature is the titanium carbide sizing ring. Titanium carbide has the highest hardness of any readily available carbide, and under a microscope its microstructure looks smooth and rounded, which gives you a slippery, non-galling surface that lets you resize brass without any case lube at all. For straight-wall revolver cases that you're cranking out by the hundreds, skipping the lube step is a real time and mess saver.
What You Get in the Redding .38/.357 Die Set
This is a conventional three-die arrangement built for single-stage or turret presses. The carbide sizing die handles full-length resizing and knocks out the spent primer with its decapping unit. The expander die bells and flares the case mouth just enough to seat a bullet cleanly without shaving lead or copper. The seating die rounds things out with a built-in crimp, so you can seat and crimp in one motion or split those into separate steps for the kind of consistency that matters when you're chasing tighter groups.
How the Redding Carbide Die Set Crimps
Since .38 Special and .357 Magnum are rimmed, roll-crimp cartridges, this set ships with a profile crimp built into the seater rather than a taper crimp. That matters for revolver loads, especially heavier bullets where bullet pull under recoil is a concern. Seating so the crimp catches the cannelure gives you solid neck tension and ammo that chambers and shoots reliably round after round.
These dies use the standard 7/8-14 thread, so they'll screw right into just about any common press. Keep in mind the shellholder is sold separately, so grab the correct one for the .38/.357 rim if you don't already have it on the bench. Made in the USA by one of the most respected names in reloading, this set is built to run for decades.
Key Specifications
- Caliber: .38 Special / .357 Magnum
- Die Type: Conventional 3-Die Set (Sizing, Expanding, Seating)
- Sizing Die Material: Titanium Carbide
- Crimp Style: Built-in Profile Crimp (roll crimp)
- Thread: Standard 7/8"-14
- Press Compatibility: Single-stage or turret presses
- Lube Required: No, lube-free carbide sizing
- Country of Origin: Made in the USA
- Manufacturer: Redding
- Manufacturer Part Number: 88282
- UPC: 611760882821
- Shipping Weight: 1.64 lbs
What’s Included
- Titanium carbide sizing die with decapping unit
- Expander die for flaring the case mouth
- Bullet seating die with built-in crimp
- Plastic die storage box
- Spare decapping pin
Frequently Asked Questions
Do I need case lube with the Redding Carbide 3-Die Set?
No, that's the whole point of the titanium carbide sizing die. The ultra-hard, smooth carbide ring resizes brass without galling, so you can skip the lube step entirely when sizing your .38 Special and .357 Magnum cases. That saves time and keeps your brass clean when you're loading in volume.
Does this set include a shellholder?
No, the shellholder is sold separately. You'll need the correct shellholder for the .38 Special/.357 Magnum rim, which both cartridges share. If you already load similar rimmed cases you may have the right one on your bench.
What kind of crimp does the seating die put on?
Because .38 Special and .357 Magnum headspace on the rim, this set comes with a profile crimp built into the seater rather than a taper crimp. That gives you a roll-style crimp into the bullet's cannelure, which is exactly what you want for revolver loads and heavier magnum bullets. You can seat and crimp together or run them as separate steps for extra consistency.
Will these dies fit my press?
Yes, they use the standard 7/8"-14 thread found on the vast majority of reloading presses. The set is designed primarily for single-stage and turret presses. Just thread them into your press stations and set your adjustments.




Reviews
There are no reviews yet.