0
0

Hornady Match Grade Bushing .258 Diameter Neck Sizing Bushing

UPC: 090255592580

$23.99

2 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

The Hornady Match Grade Bushing in .258" diameter is the small part that lets you take real control over neck tension on your reloads. It's a self-centering, interchangeable bushing made to drop into Hornady's Match Grade Bushing Dies, and it sizes only the case neck rather than hammering the whole thing into submission. The .258 size falls in the 6mm family, so it's a common pick for reloaders working with 6mm and .243-based cartridges, though the right number for your rig always comes down to your brass and the tension you're after.

Why the .258 Match Grade Bushing Matters at the Press

Fixed sizing dies squeeze every neck to the same spot no matter how thick your brass is, which overworks it and shortens case life. A bushing setup skips that problem. The free-floating, self-centering design keeps the neck concentric through the sizing stroke, and that consistency is what shows up downRange as tighter groups. The bushing sizes most of the neck and leaves a little at the base untouched, which is normal and part of how it keeps tension even.

Picking the Right Hornady Bushing Size

Bushing selection is simple once you know your brass. Measure the outside diameter of a loaded neck and subtract roughly .002" to .003" to land on your bushing, which allows for brass springback and gives you around .001" to .002" of neck tension. You can also measure neck wall thickness, double it, add your bullet diameter, then subtract for tension. Because different brass brands and lots vary in neck wall thickness, most folks who run bushing dies end up keeping a size above and below their target on hand to fine-tune.

Fitment and Everyday Use

This bushing works in both the Hornady Match Grade full-length and neck sizing dies, and Hornady builds them to be compatible with other common bushing-style dies like Redding, RCBS, and L.E. Wilson. Install it with the size marking facing up so you can read it at a glance. Hornady offers these in .001" increments across the lineup, so once you've nailed down your load you can repeat it lot after lot without guesswork.

Key Specifications

  • Manufacturer: Hornady
  • Bushing Diameter: .258 inch
  • Caliber Family: 6mm
  • Type: Self-Centering Neck Sizing Bushing
  • Increment Availability: .001 inch
  • Compatibility: Hornady Match Grade full-length and neck sizing dies; also Redding, RCBS and L.E. Wilson bushing-style dies
  • Finish: Polished steel
  • Quantity: 1 (sold individually)
  • Manufacturer Part Number: 594258
  • UPC: 090255592580

What’s Included

  • One (1) Hornady Match Grade .258" neck sizing bushing

Frequently Asked Questions

What cartridges is the .258 Match Grade Bushing used for?

The .258" diameter falls in Hornady's 6mm bushing range, so it's a common choice for reloaders working with 6mm and .243-based cartridges. That said, the correct bushing for your load depends on your specific brass and how much neck tension you want, not just the caliber. Measuring a loaded round is the only way to be sure.

How do I know if the .258 is the right size for my brass?

Measure the outside diameter of a loaded case neck with a good micrometer, then subtract about .002" to .003" to find your bushing. That math accounts for brass springback and leaves you with roughly .001" to .002" of neck tension. Since neck wall thickness varies by brass brand and lot, many reloaders keep one size up and one size down from their target on hand.

Does this bushing work in both the neck sizing and full-length dies?

Yes. The Hornady Match Grade bushings are interchangeable and work in both the Match Grade full-length sizing die and the neck sizing die. Hornady also builds them to be compatible with other bushing-style dies including Redding, RCBS, and L.E. Wilson.

Is a die included, or is this just the bushing?

This is the bushing only, sold individually. It's the insert that drops into a Hornady Match Grade Bushing Die, which is purchased separately. Install it with the stamped size facing up so you can read it when it's seated in the die.

Additional information

UPC

090255592580

Manufacturer

Manufacturer Part Number

594258

Shipping Weight

0.025

Reviews

There are no reviews yet.

Be the first to review “Hornady Match Grade Bushing .258 Diameter Neck Sizing Bushing”