Description
The Winchester Invector-Plus Signature Skeet choke is built for the close, fast stuff. With a light .005 constriction, it throws a wide, open pattern that gives you a bit more room for error on skeet stations, sporting clays presentations up close, and any target that breaks quick. It's the same factory-grade tube that ships with many Winchester over/unders and semi-autos, so if you're replacing a lost one or setting up both barrels the same, this is a straight match.
What Sets the Signature Skeet Tube Apart
The Signature series runs an extended body that sticks out about 3/4 inch past the muzzle. That extra length does two things: it gives the shot column a longer, smoother taper for more uniform patterns with fewer fliers, and it puts a knurled finger grip right at your fingertips. You can back this one out and swap tubes without digging around for a wrench, which is a real plus when you're moving between stations or changing loads on the fly. The signature red band on the front makes it easy to spot your constriction at a glance.
Fit and Materials on the Invector-Plus Skeet Choke
Machined from 17-4 stainless steel, this tube is tough enough to handle steel, lead, and non-toxic shot without complaint. It uses the proven Invector-Plus system, which works alongside back-boring to seal off gas between the tube and barrel for consistent, dense patterns and long-term durability. It fits 12 gauge Winchester Model 101, Supreme, Select, SX2, SX3, and SXP shotguns, and it'll drop right into Browning barrels threaded for Invector-Plus as well.
At roughly 3.2 ounces and optimized for around 30 yards, this is the tube to reach for when your targets are close and you want the widest, most forgiving pattern in the Signature lineup. Pick up a second one if you want both barrels choked the same for those quick doubles.
Key Specifications
- Manufacturer: Winchester
- Manufacturer Part Number: 6130773
- UPC: 048702178771
- Model: Signature Invector-Plus
- Gauge: 12 Gauge
- Choke Size: Skeet
- Constriction: .005
- Configuration: Invector-Plus
- Type: Extended
- Material: 17-4 Stainless Steel
- Finish: Stainless
- Diameter: 0.735 in
- Weight: 3.2 oz
- Approved Shot: Steel, Lead, Non-Tox
- Recommended Distance: 30 yards
- Chokes Included: One Choke
What’s Included
- One Winchester Invector-Plus Signature Skeet choke tube (.005)
Frequently Asked Questions
What shotguns does this Invector-Plus Signature Skeet choke fit?
It's made for 12 gauge Winchester shotguns including the Model 101, Supreme, Select, SX2, SX3, and SXP. It also fits Browning barrels that are back-bored and threaded for the Invector-Plus system, so if your Browning uses Invector-Plus tubes, this one drops right in. Just confirm your barrel is marked Invector-Plus and not standard Invector before ordering.
Can I shoot steel shot through the Skeet choke?
Yes. The 17-4 stainless steel construction is rated for steel, lead, and non-toxic shot, so you're covered whether you're breaking clays or running waterfowl loads. The Invector-Plus design also seals gas between the tube and barrel, which helps it hold up over the long haul with harder steel loads.
What is a Skeet choke best used for?
The Skeet constriction is very open, throwing a wide pattern that spreads quickly. That makes it ideal for close-range targets like skeet stations and up-close sporting clays presentations where birds break fast and you want a more forgiving spread. It's the go-to when your shots are inside about 25 yards.
Do I need a wrench to install this extended choke?
No wrench required. This Signature tube extends past the muzzle and has a knurled finger grip, so you can thread it in and out by hand. That makes swapping tubes between stations or changing loads a lot quicker and means one less tool to keep track of.




Reviews
There are no reviews yet.