Description
Reloads live and die on that split-second window when you line up a fresh magazine with the grip. The Smart Lock Technology XD EasyFit Magwell widens that target for you, flaring out the bottom of your Springfield XD so the magazine drops in clean instead of hanging up on an edge. It's a simple add-on that pays off every time you hit the mag release, whether you're running a timer at the range or just want smoother manipulation.
What the XD EasyFit Magwell Brings to the Grip
This one is built from glass-filled nylon polymer in a matte black finish, so it matches the lines of the XD without adding noticeable weight. The whole piece tips the scales at right around a third of an ounce, measures about 2 3/8 inches long, and runs roughly 1.47 inches wide to match the 9mm and .40 S&W frame. Beyond speeding up reloads, the molded polymer body also wraps the opening of your magwell and takes the abuse of hard mag slams so the frame itself doesn't get chewed up over time.
Fitting the EasyFit Magwell to Your XD
Installation lives up to the name. You back out the attached screw, slide the magwell up into the bottom of the grip, confirm it's seated snug, and then tighten the included steel retention screw to lock it in place. No gunsmithing, no permanent changes to the pistol. Worth noting that this is sized for the full-size service and tactical XD and HS2000 models in 9mm or .40 S&W, not the compact or sub-compact frames, and some XD models produced after March 2005 have a little material inside the grip that may need light trimming for a flush fit.
If you shoot your XD often and want a faster, more consistent reload without spending big on a machined aluminum setup, this is an easy upgrade to drop in and forget about.
Key Specifications
- Manufacturer: Smart Lock Technology, Inc.
- Model: XD
- UPC: 625214016205
- Caliber Fit: 9mm / .40 S&W
- Fits: Full-size Springfield XD and older HS2000, 4" Service and 5" Tactical models
- Does Not Fit: Compact or sub-compact frames
- Material: Glass-filled nylon polymer
- Color: Black
- Finish: Matte
- Length: Approx. 2 3/8 in (5.8 cm)
- Width: Approx. 1.47 in (37.5 mm)
- Weight: Approx. 0.34 oz (9.6 g)
- Installation: Bolt-on with included steel retention screw
What’s Included
- XD EasyFit Magwell (9mm/.40 S&W)
- Steel retention screw
Frequently Asked Questions
Will the XD EasyFit Magwell fit my pistol?
This version is made for the full-size Springfield XD and older HS2000 models chambered in 9mm or .40 S&W, including the 4-inch Service and 5-inch Tactical frames. It does not fit compact or sub-compact models, and there's a separate version for .45 ACP. If you've got a full-size XD in 9mm or .40, you're good.
How hard is it to install the EasyFit Magwell?
It's about as simple as it gets. You back out the attached screw, slide the magwell up into the bottom of the grip until it seats snug, then tighten the included steel retention screw to hold it in place. No gunsmithing or permanent modifications to the pistol are needed.
Does the XD EasyFit Magwell actually speed up reloads?
Yes, that's the whole point of it. By flaring out the opening at the base of the grip, it gives you a bigger target to guide the magazine into, which means fewer fumbles when you're reloading under pressure or against a timer. It also shields the magwell opening from wear caused by hard magazine insertions.
Some listings mention trimming. What's that about?
Certain Springfield XD models made after March 2005 have a bit of extra material inside the grip hole that can keep the magwell from seating flush. On those pistols, a little light trimming of that blockage lets the magwell fit properly. Most full-size XDs drop it right in without any work.




Reviews
There are no reviews yet.