Description
The EGW Tikka T3x TAC A1 one-piece Picatinny base is purpose-built for one rifle and one rifle only, and that focus shows. This is the heavy-duty version of EGW's Tikka lineup, machined from a solid block of 7075 T6 aircraft-grade aluminum rather than extruded stock, then tumbled, sand blasted, and finished in a Type III hard-coat anodize that holds up to recoil, weather, and years of range time. The 20 MOA of built-in cant tilts your optic forward so you keep more of your scope's internal elevation in the tank, which is exactly what you want once targets start getting far away.
Why 20 MOA Matters on the TAC A1
The angle machined into this base is the whole point. EGW suggests a 0 MOA rail if most of your shooting stays inside 500 yards, and the 20 MOA option like this one once you start reaching past that, out toward the 1,000-yard range. That forward cant preserves usable turret travel so your scope isn't bottomed out when you dial for distance. A common tip is to zero at 200 yards when running a 20 MOA base, which leaves plenty of adjustment on tap for everything beyond.
Built to Fit the Tac A1 Right
Unlike standard T3 and T3x rails, this one is cut specifically for the Tac A1 receiver, so the hole spacing and profile line up the way they should. It runs a 3.245-inch center spread and a 6.761-inch overall length, weighs in around 2.5 ounces, and the Picatinny cross slots run the full length of the rail gauged to MIL-STD 1913 spec. That gives you room to slide rings fore and aft for proper eye relief, and it plays nice with both Picatinny and Weaver rings. It's also ambidextrous and quick-disconnect ring compatible.
Installation is straightforward with the included hardware. EGW recommends 20 inch-pounds of torque and a drop of blue thread locker to keep everything locked in under recoil. Keep in mind the original front screw lives under the handguard, so you'll remove the handguard to pull the factory mount before this one goes on.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 80512
- UPC: 841370117284
- Fits: Tikka T3x TAC A1
- Rail Type: One-Piece Picatinny
- Elevation / Cant: 20 MOA
- Material: Solid 7075 T6 Aircraft-Grade Aluminum
- Finish: Matte Black Type III Hard-Coat Anodized
- Center Spread: 3.245 in
- Overall Length: 6.761 in
- Weight: 2.5 oz
- Ambidextrous: Yes
- Quick Disconnect Ring Compatible: Yes
- Ring Compatibility: Picatinny or Weaver
- Torque Spec: 20 in-lbs
- Made In: USA
What’s Included
- One-piece Picatinny rail base
- (5) #6-48 x 1/4 mounting screws
- (2) recoil pins
- T-10 wrench
Frequently Asked Questions
Will this EGW base fit a standard Tikka T3 or T3x?
No, this rail is machined specifically for the Tikka T3x TAC A1 receiver and its unique mounting setup. Standard T3 and T3x rifles use a different EGW rail. If you have a Tac A1, this is the dedicated base you want.
Should I go with the 20 MOA or a 0 MOA base?
The 20 MOA cant is the pick if you plan to dial elevation and shoot past roughly 500 yards, out toward 1,000. It preserves more of your scope's internal travel for long-range work. If most of your shooting stays inside 500 yards, a 0 MOA rail is the more neutral choice.
Does the Tac A1 base work with Picatinny and Weaver rings?
Yes. The cross slots are machined to MIL-STD 1913 Picatinny spec and run the full length of the rail, so it accepts both Picatinny and Weaver style rings. It's also quick-disconnect ring compatible for optics you want to pull on and off.
What do I need to know about installing it?
The base comes with the screws, recoil pins, and a T-10 wrench. EGW recommends torquing to 20 inch-pounds with a drop of blue thread locker. Note that the factory front screw sits under the handguard, so you'll remove the handguard to get the original mount off before installing this one.





Reviews
There are no reviews yet.