Description
Getting a quality optic onto an old Swedish Mauser has always been a bit of a project, and this is the part that makes it painless. The EGW Swedish Mauser 3-Hole w/ Hump is a one-piece Picatinny rail machined specifically for the small ring military Swedish Mauser, the kind with that distinctive stripper clip hump on the receiver. It gives you a solid, modern mounting platform without hacking up a classic rifle any more than the drill-and-tap job already requires.
This particular version carries 20 MOA of built-in elevation cant, which tilts your scope forward to give you more usable adjustment for longer shots. EGW's own guidance is simple: 0 MOA suits 0 to 500 yards, while the 20 MOA is the pick if you're stretching things out toward 1000. If you go the 20 MOA route, a 200-yard zero is a good starting point. The full-length Picatinny cross slots run the whole rail, so you've got plenty of room to position rings exactly where eye relief wants them.
What Makes the Swedish Mauser 3-Hole Rail Tick
EGW cuts these from domestic 6061 T6 extruded aluminum on their USA-made machining centers, then tumbles, sand blasts, and Type II anodizes them in a matte black finish for durability that holds up to real field use. The mount runs 6.670 inches overall with a 4.275 inch center spread between the two middle receiver holes, sits about 0.4 inches high from the top of the receiver, and tips the scale around 2 ounces. There's a relief channel milled down the center that trims weight and, in many cases, leaves your factory iron sights usable underneath.
Fit and Install Notes for Your Mauser
It's cut with bevels on both sides, so it works for righties and lefties alike. Mounting hardware comes in the box, and EGW recommends torquing to 20 inch pounds with a drop of blue Loctite to keep everything locked down under recoil. Since these old receivers vary, measuring your hole spacing against the published 4.275 inch center spread before you start is time well spent. Pair it with a set of standard Picatinny or Weaver rings and you've got a sharp-shooting Swede ready for glass.
Key Specifications
- Manufacturer: Evolution Gun Works (EGW)
- Manufacturer Part Number: 47032
- UPC: 841370112395
- Fits: Small Ring Military Swedish Mauser w/ Hump (96, 94, 38, 41)
- Rail Type: One Piece Picatinny
- Cant: 20 MOA
- Material: Domestic 6061 T6 Extruded Aluminum
- Finish: Matte Black Type II Anodizing
- Overall Length: 6.670 in
- Center Spread: 4.275 in
- Height: 0.4 in (top of receiver to top of rail)
- Weight: Approx. 2 oz
- Hole Size: .332 in
- Ambidextrous: Yes, beveled both sides
- Mounting Hardware: #6-48 x 1/4 screws and T-10 bit included
- Made In: USA
What’s Included
- Swedish Mauser 3-Hole w/ Hump 20 MOA Picatinny scope mount
- #6-48 x 1/4 mounting screws
- T-10 bit/wrench
Frequently Asked Questions
Which rifles does the Swedish Mauser 3-Hole w/ Hump mount fit?
This base is cut for the small ring military Swedish Mauser with the stripper clip hump on the receiver, which covers the Model 96, 94, 38, and 41. Because these are vintage receivers that can vary slightly, it's smart to measure your hole spacing against the 4.275 inch center spread before installing. It does not fit large ring 98-pattern Mausers.
What does the 20 MOA cant actually do for me?
The 20 MOA builds a forward tilt into the rail, giving your scope more elevation adjustment for longer-range shooting. EGW suggests the 20 MOA version for distances stretching from about 500 out to 1000 yards. If you go this route, zeroing at 200 yards is a solid starting point.
Does this mount require drilling and tapping?
Yes. This is a three-hole base, and most military Swedish Mauser receivers will need to be drilled and tapped in the correct locations to accept it. If you're not set up for that, a gunsmith can handle the job quickly.
What rings work with this rail, and how should I install it?
It's a Picatinny-style base, so any standard Picatinny or Weaver rings will clamp right on. EGW recommends torquing the base screws to 20 inch pounds with a drop of blue Loctite so nothing walks loose under recoil. The mounting screws and bit are included in the box.




Reviews
There are no reviews yet.