Description
Strike Industries built the Venom Flash Hider to do one job extremely well: kill muzzle flash on big-bore AR-platform rifles. Machined from steel with a black finish, it threads onto standard 5/8×24 barrels chambered in .308 Winchester or 7.62x51mm NATO, which covers the vast majority of AR-10 and large-frame builds out there. No permanent modifications to the rifle are needed to run it.
The heart of the design is four prongs tipped with serrated points. That geometry creates instant airflow at the muzzle and disrupts gas combustion the moment the round leaves the barrel, which is what lets the Venom knock out close to 100 percent of visible flash. Cut the flash and you keep your night vision and situational awareness intact, so getting back on target for that next shot happens quicker in low light. The open-prong shape also wraps and protects the muzzle crown, and it just plain looks aggressive on the end of a barrel.
What Makes the Venom .308 Flash Hider Tick
At roughly 2.16 inches long with a 0.862-inch outer diameter and a weight around 3 ounces, the Venom stays lean and doesn't add noticeable heft to the front of your rifle. Real-world feedback backs up the flash numbers too, with owners reporting essentially zero visible flash even off shorter barrels where flash is usually a bigger problem.
Getting the Venom FH Installed Right
Installation is straightforward for anyone comfortable swapping a muzzle device. Time the device the way you want it, and Strike Industries recommends torquing it down in the 15 to 20 ft-lb range to seat it properly against the crush washer. Builders running 14.5-inch barrels will appreciate that the Venom is long enough to bring that barrel up to 16 inches, and it comes with a pre-drilled hole for pinning and welding if that's the route you're going. Whether it's headed to the range or the field, this is a proven, budget-friendly way to tame flash on a .308 AR.
Key Specifications
- Manufacturer: Strike Industries
- Model: Venom
- Product Type: Flash Hider
- Manufacturer Part Number: VENOMFH308
- UPC: 700598351057
- Caliber: .308 Win / 7.62x51mm NATO
- Thread Pattern: 5/8×24 tpi
- Prong Design: Four-prong with serrated points
- Material: Steel
- Finish: Black
- Overall Length: 2.16 in
- Outer Diameter: 0.862 in
- Weight: 3 oz
- Recommended Torque: 15-20 ft-lbs
- Pin & Weld Ready: Yes, pre-drilled hole
What’s Included
- Venom Flash Hider
- Crush washer
Frequently Asked Questions
What rifles does the Venom .308 flash hider fit?
It's built for AR-platform and large-frame rifles chambered in .308 Winchester or 7.62x51mm NATO that use 5/8×24 threading, which includes most AR-10 builds. As long as your barrel is threaded 5/8×24, the Venom will thread right on with no permanent modifications to the rifle.
Can I pin and weld the Venom FH to make a 14.5-inch barrel legal length?
Yes. The Venom is long enough to bring a 14.5-inch barrel up to the 16-inch mark, and it ships with a pre-drilled hole that makes pinning and welding a clean job for your gunsmith. That's a popular reason builders reach for this particular flash hider.
How well does the Venom actually reduce muzzle flash?
The four-prong serrated design creates instant airflow that disrupts gas combustion at the muzzle, knocking out close to 100 percent of visible flash. Owners running it on shorter barrels consistently report seeing essentially no flash, which helps keep your night vision and sight picture intact for faster follow-up shots.
What torque should I use when installing the Venom flash hider?
Strike Industries recommends torquing the Venom to 15 to 20 ft-lbs against the included crush washer. Time it so the prongs sit where you want them, then snug it down within that range to seat it properly and keep it from backing off.






Reviews
There are no reviews yet.