Description
The receiver extension end plate and castle nut usually get zero attention until you want to swap a stock or add a sling point, and then the peened castle nut turns a simple job into a headache. Strike Industries built the Multi-Function End Plate (MFEP) and Anti-Rotation Castle Nut (ACN) to fix that. Instead of staking or peening the nut in place, the system uses a set screw to lock everything down, so you can loosen it, make changes, and button it back up as many times as your build needs.
What the MFEP End Plate Brings to Your Build
The end plate is reversible and gives you three integral sling mounting points, including sling loops on both sides and an anti-rotation QD socket. Because it flips, you can orient the loop to whichever side matches how you run your sling, whether you shoot lefty, righty, or just like your hardware set up a certain way. There is also a set screw on the plate itself that holds your takedown pin detent and spring in place, which means no more chasing a launched spring across the shop floor during install.
Anti-Rotation Castle Nut That Stays Put
The ACN is machined to work specifically with this end plate and locks in with a dedicated anti-rotation set screw rather than traditional peening. It holds tension on your receiver extension the way it should while staying fully serviceable down the road. Keep in mind you do not want to torque the castle nut past 35 ft-lbs.
Built Light in Flat Dark Earth
Both pieces are cut from ultralight 7075-T6 aluminum and finished with a Flat Dark Earth anodizing that ties in nicely with an FDE or two-tone build. The end plate weighs about a quarter ounce and the castle nut runs roughly 0.63 ounces, so you get real functionality without adding any meaningful weight. Fitment covers Mil-Spec AR-15 and AR-10 ArmaLite/DPMS pattern receivers, making this a clean upgrade for just about any standard build.
Key Specifications
- Manufacturer: Strike Industries
- Manufacturer Part Number: ARULMFEP&ACNFDE
- Model: SI-AR-UL-MFEP&ACN-FDE
- UPC: 793811764482
- Color: Flat Dark Earth
- Material: 7075-T6 Aluminum
- Finish: Anodized
- End Plate Weight: 0.25 oz
- Castle Nut Weight: 0.63 oz
- Sling Mounting Options: Three (dual sling loops plus anti-rotation QD socket)
- Retention Method: Set screw (no peening or staking)
- Max Castle Nut Torque: 35 ft-lbs (47.45 Nm)
- Compatibility: Mil-Spec AR-15 and AR-10 ArmaLite/DPMS pattern receivers
What’s Included
- 1x Multi-Function End Plate
- 1x Anti-Rotation Castle Nut
- 1x Detent Set Screw
- 1x Anti-Rotation Set Screw
Frequently Asked Questions
Does the Multi-Function End Plate work on both AR-15 and AR-10 rifles?
Yes. It is designed to fit Mil-Spec AR-15 and AR-10 ArmaLite/DPMS pattern receivers, so it covers the vast majority of standard builds. As long as your receiver extension is Mil-Spec, you are good to go.
Do I still need to peen or stake the castle nut?
No, and that is the whole point of this design. The Anti-Rotation Castle Nut locks in with a set screw instead of peening or staking, which means you can remove it later and rebuild or swap parts without destroying anything. Just remember to keep torque at or below 35 ft-lbs.
What sling attachment options does the MFEP give me?
You get three integral options: sling loops on both sides of the plate plus an anti-rotation QD socket. The plate is reversible, so you can flip it to run your preferred loop on either side depending on how you carry the rifle.
What tool do I need to install it?
You will need a 1.5mm hex key to work the detent set screw and the anti-rotation set screw, and it is not included in the box. A standard armorer's wrench handles tightening the castle nut. The plate's built-in set screw also holds your takedown pin detent and spring so they do not launch during assembly.




Reviews
There are no reviews yet.