Description
Springfield built the Agency Optic System to make red dot mounting on the 1911 DS clean and repeatable, and this A12B plate is the piece that ties it all together. Developed alongside Agency Arms, it drops into the AOS cut on your slide and gives you a proper footprint for micro reflex optics without stacking adapter plates or guessing at screw lengths. The plate carries a serrated black notch rear sight on the rear dovetail, so you keep usable irons even before you bolt on glass.
What the A12B Plate Fits
This is the A12B footprint, which is the one you want for smaller micro optics. It is cut for the HEX Wasp, Holosun 507K-X2 and 407K-X2, Shield RMSc, SMSc and RMS2, and the Swampfox Sentinel. The HEX Wasp and the Shield optics run on the optic maker's supplied screws, while the Holosun 507K and 407K may call for a screw swap or slight modification to seat correctly. If you are running a 507C, 508T or an RMR, those are a different plate, so match your optic to the A12B code before ordering.
Built From Billet Steel
Springfield machines these plates from billet steel and finishes them in black, which is why they hold a zero and shrug off recoil cycle after cycle. Users running the plate with a 507K have reported it staying dead on past a few hundred rounds without backing out. The integral rear sight is the real difference between this and a generic aluminum adapter, since it sets the correct optic height for a natural sight picture and keeps a back-up aiming reference on the gun.
Getting It On Your 1911 DS
Installation is straightforward on any AOS-equipped 1911 DS. Pull the factory cover plate, which takes the old rear sight with it, then set the A12B in place with the included hardware and mount your optic on top. It is a smart upgrade for carry, competition, or range work where you want a low, repeatable red dot setup on your Prodigy or other AOS 1911 DS.
Key Specifications
- Manufacturer: Springfield Armory
- Manufacturer Part Number: PH5077N-WASP-PLT-RET
- UPC: 706397961374
- Model: Agency Optic System (AOS) Mounting Plate, A12B
- Fits: Springfield 1911 DS (AOS cut)
- Compatible Optics: HEX Wasp, Holosun 507K-X2 / 407K-X2, Shield RMSc / SMSc / RMS2, Swampfox Sentinel
- Material: Billet Steel
- Finish: Black
- Rear Sight: Integral serrated black notch rear sight
- Shipping Weight: 0.1 lbs
What’s Included
- A12B AOS mounting plate
- Integral rear sight (installed on plate)
- Mounting screws for the 1911 DS
Frequently Asked Questions
Which optics work with the A12B plate?
The A12B is cut for micro reflex optics including the HEX Wasp, Holosun 507K-X2 and 407K-X2, Shield RMSc, SMSc and RMS2, and the Swampfox Sentinel. The HEX Wasp and Shield optics mount with their factory supplied screws, while the Holosun 507K and 407K may need a screw swap or minor modification to seat properly. Larger optics like the 507C, 508T and Trijicon RMR use a different AOS plate.
Does this plate come with a rear sight?
Yes. The A12B has an integral serrated black notch rear sight installed on the rear dovetail. That keeps a usable back-up aiming reference on the gun and sets the proper optic height for a clean sight picture.
Will this fit any 1911 DS?
It is designed for Springfield 1911 DS pistols equipped with the Agency Optic System cut, such as the Prodigy. When you remove the factory AOS cover plate the old rear sight comes off with it, then the A12B drops into that same cut using the included screws.
What is the plate made of and will it hold zero?
Springfield machines these from billet steel and finishes them black, so they are built to take the pounding of regular shooting. Users running a 507K on this plate have reported it staying zeroed past several hundred rounds without the hardware loosening.





Reviews
There are no reviews yet.