Description
The Sig Sauer Alpha3 Scope Mount/Ring Combo takes the guesswork out of getting a 34mm optic mounted straight, level, and locked down. This is a one-piece design, which means the base and rings are a single unit rather than separate pieces you have to align yourself. That translates to fewer alignment headaches and a scope that holds zero shot after shot. It clamps directly to any standard Picatinny rail and sits at a 1.535-inch centerline height, putting your optic at a low, natural position above the bore.
What Sets the Alpha3 34mm Mount Apart
Sig built this mount from 7075-T6 aircraft-grade aluminum, which is the same alloy you'll find on serious precision rigs. The hardware is titanium, so you get real strength without piling on extra weight, and the whole thing tips the scale right around half a pound. The rings are machined to wrap evenly around the scope tube, giving you consistent clamping pressure all the way across so your optic isn't getting pinched or torqued unevenly. The Flat Dark Earth anodized finish shrugs off the elements and happens to look right at home on a modern tactical build.
Getting Your Optic Dialed In with the Alpha3
Installation is about as simple as it gets. The mount uses a 1/2-inch nut to clamp to the rail and a four-screw ring design per ring to hold the scope, which keeps your optic from walking under recoil. Sig's recommended torque is 65 in/lbs on the rail nut and 25 in/lbs on the T15 Torx ring screws. A good tip from folks who've run these: snug the ring screws down in small, alternating passes so the top strap seats evenly against the tube. Use a quality torque wrench and you'll be rewarded with a mount that just stays put.
This combo is a smart match for precision long-range setups and tactical platforms alike, and it carries Sig Sauer's Infinite Guarantee behind it.
Key Specifications
- Manufacturer: Sig Sauer Electro-Optics
- Model: Alpha3
- Manufacturer Part Number: SOA30014
- UPC: 798681666652
- Tube Diameter: 34mm
- Centerline Height: 1.535 in
- Material: 7075-T6 Aluminum
- Hardware: Titanium
- Mount Type: Picatinny Rail
- Design: One-Piece Mount/Ring Combo
- Color/Finish: Flat Dark Earth Anodized
- Weight: 0.54 lbs
- Rail Torque: 65 in/lbs (1/2in Nut)
- Ring Torque: 25 in/lbs (T15 Torx)
- Warranty: Sig Sauer Infinite Guarantee
What’s Included
- Sig Sauer Alpha3 34mm one-piece scope mount/ring combo
- Titanium mounting hardware
Frequently Asked Questions
What size scope tube does the Sig Sauer Alpha3 SOA30014 fit?
This mount is built specifically for riflescopes with a 34mm maintube. If your optic has a 30mm tube, you'll want the 30mm version of the Alpha3 instead, since the rings are sized for 34mm and won't properly clamp a smaller tube.
Will the Alpha3 mount fit my rifle?
The Alpha3 clamps to any standard Picatinny rail, so it'll work on most modern rifles with a flat-top receiver or a rail-equipped action. It attaches using a 1/2-inch nut on the rail clamp. Just make sure you have enough rail real estate for the one-piece base.
What are the torque specs for mounting the Alpha3?
Sig calls for 65 in/lbs on the 1/2-inch rail nut and 25 in/lbs on the T15 Torx ring screws. A good practice is to tighten the ring screws in small alternating passes so the top strap seats evenly across the scope tube. Using a proper inch-pound torque wrench is well worth it to avoid over-tightening.
What is the mounting height of the Alpha3 34mm combo?
It has a 1.535-inch centerline height, measured from the rail to the center of the scope tube. That's a comfortable, relatively low position that works well for a natural cheek weld on most precision and tactical builds.




Reviews
There are no reviews yet.