Description
The Raptor TSS from Rob Roberts Gun Works is a wing-shooting choke tube built with one job in mind: getting the absolute best pattern out of premium tungsten super shot. TSS is heavier and denser than lead, which means it behaves differently going through a choke. Rob Roberts tuned this tube's internal geometry specifically for that dense shot, so you get the tight, even patterns that make long shots on ducks and turkeys a whole lot more forgiving.
What Sets the Raptor TSS Apart
This one is machined from 17-4 PH U.S. stainless steel, the same tough, corrosion-resistant material Rob Roberts uses across the RRaptor lineup. It's cut on state of the art equipment to tolerances that go well past the industry standard, which is a big part of why these tubes pattern so consistently. The exterior wears green Cerakote and features machined claw marks instead of traditional knurling, so you can grab it and snug it down by hand even with cold, wet fingers in the blind.
Fitment and Setup for Your Raptor TSS
This version is threaded for the Standard Invector system, so it drops into shotguns marked Invector or Standard Invector, including plenty of older Browning and Winchester models along with certain Mossberg guns. Standard Invector and Invector-Plus are not interchangeable, so check the stamp on your barrel near the muzzle or receiver before ordering. It's a straightforward twist-in install, no gunsmithing required.
One thing worth knowing if you shoot an over-under: a Raptor choke is designed to run in a single barrel only, not both. For semi-autos and pumps that's a non-issue, and either way you're getting a purpose-built tube that turns pricey TSS loads into their best possible performance downrange. If you've invested in tungsten ammo, this is the choke that helps you cash in on it.
Key Specifications
- Manufacturer: Rob Roberts Gun Works
- Model: Raptor TSS
- Manufacturer Part Number: 200282
- UPC: 810174901917
- Gauge: 12 Gauge
- Choke System: Standard Invector
- Optimized For: TSS (Tungsten Super Shot)
- Material: 17-4 PH U.S. Stainless Steel
- Finish: Green Cerakote
- Grip: Machined claw marks
- Intended Use: Waterfowl and turkey wing shooting
What’s Included
- Rob Roberts Raptor TSS choke tube (1)
Frequently Asked Questions
What kind of ammo is the Raptor TSS choke made for?
This tube is tuned specifically for premium tungsten super shot (TSS), which is denser and heavier than lead and patterns differently through a choke. Running TSS through the Raptor TSS gets you tighter, more consistent patterns than a general-purpose tube would. It's a favorite among waterfowl and turkey hunters who've invested in high-density loads.
Will the Raptor TSS fit my shotgun?
This version is threaded for the Standard Invector system, so it fits shotguns marked Invector or Standard Invector, including many older Browning and Winchester models plus certain Mossberg guns. Standard Invector, Invector-Plus, and Invector-DS are not interchangeable, so check the marking stamped on your barrel before ordering. When in doubt, look near the muzzle or receiver for the system name.
What is the Raptor TSS choke tube made of?
It's machined from 17-4 PH U.S. stainless steel, a tough and corrosion-resistant alloy used across the RRaptor series. The exterior is finished in green Cerakote and features machined claw marks for grip. It's built to hold up to regular season use and stay looking good.
Can I run this choke in both barrels of my over-under?
No, a Raptor choke is designed to run in a single barrel only, and the design doesn't allow placement in both barrels of an over-under. For semi-auto and pump shotguns this is a non-issue since you're only running one choke anyway. If you shoot an O/U, plan to install it in one barrel.




Reviews
There are no reviews yet.