Description
The Final Strut is Rob Roberts' turkey-specific choke, and this version is cut for Beretta's Optima HP threading, meaning it drops right into the A400 and 1301 platforms that a lot of turkey hunters are running. It carries a .660 constriction, which is the sweet spot for wringing a dense, hard-hitting pattern out of a 12 gauge without choking things down so far that patterns start blowing apart. Roberts has spent a career dialing in shotgun patterns using computerized pattern analysis, and that work is baked into this tube.
What the Final Strut Turkey Choke Does on the Pattern Board
Paired with a quality turkey load, this choke is built to deliver clean, consistent kills past 50 yards. The whole idea here is pattern density where it counts, putting a tight cluster of pellets on a gobbler's head and neck at the distances that actually matter in the turkey woods. That said, every barrel is a little different, so pattern your gun with a couple of loads before opening morning to see what your setup likes best.
Built From 17-4ph Stainless and Made in the USA
The Final Strut is machined from 17-4ph stainless steel and heat treated, so it shrugs off lead, steel, HeviShot, and the modern tungsten super shot loads that hit turkeys so hard. It's laser engraved for easy identification when you're digging through your choke case, and it's proudly made in the USA. Tolerances are held tighter than standard factory chokes, which is a big part of why these pattern the way they do.
Fitting the Optima HP Final Strut Choke to Your Shotgun
Double-check that your shotgun uses the Beretta Optima HP thread pattern before ordering, since this tube is cut specifically for that system and won't interchange with Mobil, Invector, or Crio Plus guns. Install it in an unloaded gun, thread it in snug by hand, and give it a check now and then during a long day of hunting. Keep it clean and it'll pattern the same season after season.
Key Specifications
- Manufacturer: Johnny Stewart / Rob Roberts Gun Works
- Model: Final Strut Turkey Choke Optima HP
- Manufacturer Part Number: 200181
- UPC: 810174900903
- Gauge: 12 Gauge
- Constriction: .660
- Choke System: Beretta Optima HP (A400, 1301)
- Material: 17-4ph Stainless Steel, Heat Treated
- Design: Extended, Turkey-Specific
- Shot Compatibility: Lead, Steel, HeviShot, and Non-Toxic Loads
- Country of Origin: USA
What’s Included
- Rob Roberts Final Strut Turkey Choke (Optima HP, 12 Gauge)
Frequently Asked Questions
What shotguns does this Final Strut Optima HP choke fit?
This tube is machined for the Beretta Optima HP thread pattern, which covers popular platforms like the Beretta A400 and the 1301. It will not fit Mobil, Invector, or Crio Plus guns, so confirm your barrel uses Optima HP threading before ordering. When in doubt, check your owner's manual or the markings on your factory chokes.
What constriction is the Final Strut turkey choke and why does it matter?
This one runs a .660 constriction, which is a proven range for turkey work in a 12 gauge. It's tight enough to build a dense, concentrated pattern for head and neck shots without over-constricting to the point that patterns break apart. Pairing it with a good turkey load is where it really shines.
Can I shoot tungsten (TSS) and steel loads through the Final Strut?
Yes. The choke is made from heat-treated 17-4ph stainless steel and is rated for lead, steel, HeviShot, and other non-toxic loads, including the modern tungsten super shot turkey loads. That toughness is a big reason it holds up shot after shot.
Do I still need to pattern my shotgun with this choke?
Absolutely. Every barrel and load combination patterns a little differently, so it pays to shoot a few turkey loads at a target before the season to see which one your gun likes best. Doing this tells you your true point of impact and effective range so there are no surprises when a longbeard steps out.




Reviews
There are no reviews yet.