Description
Every clay or bird game has that shot where the target is way out there, and a run-of-the-mill choke just does not have the reach. That is exactly the gap the Rob Roberts T3 Triple Threat was built to fill. It is the tightest tube in the Triple Threat family, sitting a step above the close-range T1 and the mid-range T2, and it is the one you thread in when you need to put pellets on high flyers, long trap targets, and anything sitting at the far edge of your range.
Rob Roberts earned his reputation the hard way, by testing patterns rather than trusting old choke labels. His shop in Arkansas runs computerized pattern analyzers to fine-tune each tube around evenness instead of just the percentage of pellets inside a circle. The idea behind the whole lineup is a clean, well-distributed pattern that puts multiple hits on target no matter where the bird or clay lands in the spread, which is what actually breaks targets and folds birds at distance.
Where the T3 Triple Threat Invector Earns Its Keep
Think of the T3 as the light-full end of the range. It shines on 27-yard trap, stretched sporting clays presentations, and long shots on ducks and geese where a looser tube leaves gaps in the pattern. It is a specialist, and that focus is the point. Pair it with the T1 and T2 and you have most shooting situations covered from close to far.
Built From 17-4 PH Stainless and Ready for Any Shot
The tube is machined from 17-4 PH U.S. stainless steel, a tough, corrosion-resistant alloy that holds up to wet blinds, muddy fields, and season after season of use. It is cleared for lead, steel, and exotic non-toxic shot, so you can run the same choke through your clays rounds and your waterfowl loads without swapping tubes. This version is threaded for the standard Invector pattern found on many Browning and Winchester 20 gauge barrels, so double-check your barrel's thread pattern before ordering to make sure it is an Invector fit and not Invector-Plus.
Key Specifications
- Manufacturer: Johnny Stewart / Rob Roberts Gun Works
- Model: T3 Triple Threat
- Manufacturer Part Number: 200138
- UPC: 810174900477
- Gauge: 20 Gauge
- Thread Pattern: Invector
- Constriction Range: Long range (light-full)
- Material: 17-4 PH U.S. Stainless Steel
- Shot Compatibility: Lead, steel, and exotic non-toxic
- Country of Origin: USA
- Category: Shotgun Chokes
What’s Included
- Rob Roberts T3 Triple Threat Invector 20 gauge choke tube
Frequently Asked Questions
What kind of shooting is the T3 Triple Threat choke best for?
The T3 is the long-range tube in the Triple Threat lineup, so it is at its best on high flyers, long trap targets, and stretched-out clays and waterfowl shots. It runs roughly in the light-full range, tighter than the mid-range T2 and much tighter than the close-range T1. Reach for it when your targets are consistently sitting at the far edge of your range.
Will this choke fit my 20 gauge shotgun?
This version is machined for the standard Invector thread pattern, which is common on many Browning and Winchester 20 gauge barrels. It is not the same as Invector-Plus, so confirm which pattern your barrel uses before ordering. If your barrel is marked Invector-Plus, you will want that version instead.
Can I shoot steel and non-toxic loads through the T3 Triple Threat?
Yes. The tube is cleared for lead, steel, and exotic non-toxic shot, so one choke covers your clays practice and your waterfowl loads. The 17-4 PH stainless steel construction is built to handle harder shot types without issue.
How is the Triple Threat different from a standard modified or full choke?
Rob Roberts designs these tubes around pattern evenness rather than the traditional percentage-based choke labels. The goal is a clean, uniform spread that puts several pellets on target wherever it lands in the pattern, which tends to break clays and fold birds more reliably at distance. That is why the line uses T1, T2, and T3 names instead of skeet, modified, and full.




Reviews
There are no reviews yet.