Description
Reptilia built the CQG around a simple idea: on short, punchy guns, your hand wants to sit higher and more upright than a standard A2 grip allows. The result is a compact grip with a pronounced vertical angle that lines your wrist up more naturally behind the trigger. It was purpose-built for the rise of compact platforms like short-barreled rifles, AR pistols, PCCs, and PDWs, but it works just as well on a full-size carbine if you like a steeper hold.
The standout feature here is the shorty beavertail. It sets your hand up into the receiver, choking you closer to the bore for better control on guns run tight to the body. The angle sits right around 15 degrees, putting it in the same near-vertical camp as the B5 Type 23, a touch steeper than a Magpul K2. Front and rear texturing gives you a positive hold without chewing up your palm, and it plays nice with gloves. Reptilia molds the CQG from impact-modified reinforced nylon, so it shrugs off drops and hard use while staying light at roughly 77 grams.
Where the CQG Grip Really Shines
The slim profile is the sleeper advantage. On enclosed or high-end lowers where a chunky grip fouls the magwell flare or takedown pin, the CQG's thinner body clears the way. It's also a favorite for folks with smaller or medium hands who find bigger grips like the BCM Mod 3 a bit much to wrap around. If every ounce counts on a lightweight build, this one earns its spot.
Fitment and Install for the CQG Grip
The CQG uses the standard AR grip mounting system, so it drops onto AR-15/M16, AR-10/SR25, SIG MPX/MCX, and FN SCAR 16 and 17 pattern hosts. Installation is a two-minute job with a single grip screw and washer. Pro tip from experience: dab a little grease on the safety detent spring so it stays put while you slide the grip on, or it'll launch across the shop. Reptilia backs it with a lifetime warranty against defects, which is nice peace of mind on a part you'll bump and bang around.
Key Specifications
- Manufacturer: Reptilia
- Model: CQG Pistol Grip
- Manufacturer Part Number: 100-023
- UPC: 850002688269
- Color: Flat Dark Earth
- Material: Impact-Modified Reinforced Nylon
- Grip Angle: Near-vertical, approximately 15 degrees
- Weight: Approximately 77 grams
- Compatibility: AR-15/M16, AR-10/SR25, SIG MPX/MCX, FN SCAR 16/17
- Texture: Anti-slip front and rear
- Beavertail: Enhanced shorty beavertail
- NSN: 1015-01-674-6753
- Origin: Made in USA
- Warranty: Lifetime against manufacturer defects
What’s Included
- Reptilia CQG Pistol Grip (Flat Dark Earth)
- Grip mounting screw and washer
Frequently Asked Questions
What rifles does the Reptilia CQG grip fit?
The CQG uses the standard AR grip mounting pattern, so it fits AR-15/M16 and AR-10/SR25 receivers, plus SIG MPX/MCX and FN SCAR 16 and 17 pattern hosts. Installation is a simple single-screw swap. On some DPMS-pattern AR-10 lowers you may see a small cosmetic gap behind the beavertail, but it doesn't affect fit or function.
How does the CQG grip angle compare to a Magpul or BCM grip?
The CQG sits at a near-vertical angle of about 15 degrees, which is a few degrees steeper than a Magpul MOE-K and puts it in the same upright camp as the B5 Type 23. That more vertical pitch lines your wrist up with your forearm, which many find more comfortable on short length-of-pull guns. It's also slimmer than the BCM Gunfighter Mod 3.
Is the Reptilia CQG a good pick for smaller hands?
Yes. The slim, compact body is one of the main reasons folks with small to medium hands reach for the CQG. It fills the palm without the bulk of larger grips, and the beavertail helps you get a high, secure hold. Reviewers with average-size hands consistently mention how well it fits.
What is the CQG grip made from and how durable is it?
It's molded from impact-modified reinforced nylon, the same tough polymer family used across quality aftermarket grips. Long-term users report no cracking or deformation after range sessions and training courses. Reptilia also backs it with a lifetime warranty against manufacturer defects.





Reviews
There are no reviews yet.