Description
Mounting a scope should be the easy part of building out your Remington 700, and MDT's 20 MOA Picatinny base makes it exactly that. This is a one-piece rail machined from solid 6061-T6 aircraft grade aluminum, then given a Mil-Spec Type II hard anodized finish so it shrugs off weather, holidays in the truck bed, and years of hard use. It's cut to MIL-STD-1913 and STANAG 4694 spec, so any standard Picatinny rings clamp on without drama and you can slide them fore and aft to dial in your eye relief.
What the 20 MOA Cant Does for Your 700
The forward slope is the whole point here. That built-in 20 MOA tilt shifts your scope's usable elevation toward the top end, which means you keep more "up" travel on tap for long-range dialing instead of bottoming out your turret. If you're stretching a 6.5 Creedmoor, .308, or similar out past 600 yards, this is the base that keeps you from running out of adjustment when the distance gets honest. Just make sure your optic has enough total elevation travel to still zero comfortably at 100.
Fit and Finish on the MDT Short Action Base
The underside is contoured to sit flush against the Remington 700 short action receiver and match the geometry of the ejection port, so it seats clean with no gaps. On models where the action allows, MDT integrates a recoil lug into the rail profile for a more positive lockup. The whole rail is contoured for snag-free handling, which you'll appreciate slinging it around in the field.
Hardware and Setup
Each base ships with #6-48 Torx screws for factory drilled and tapped receivers, and the base is also drilled to accept #8-40 screws if you want to step up to beefier hardware. Snug everything down to spec, blue Loctite the screws, and you've got a rock-solid foundation for your optic that'll hold zero shot after shot.
Key Specifications
- Manufacturer: MDT
- Manufacturer Part Number: 102187-BLK
- UPC: 990482719531
- Model: Remington 700
- Fit: Remington 700 Short Action
- Action Type: Bolt Action
- Elevation: 20 MOA
- Base Type: One-Piece Picatinny
- Rail Spec: MIL-STD-1913 & STANAG 4694
- Material: 6061-T6 Aircraft Grade Aluminum
- Finish: Mil-Spec Type II Hard Anodized
- Color: Matte Black
- Mounting Hardware: #6-48 Torx (drilled for #8-40 also)
What’s Included
- MDT 20 MOA Picatinny scope base
- #6-48 Torx mounting screws
Frequently Asked Questions
Will this MDT base fit my Remington 700?
This particular base is cut for the Remington 700 short action receiver, so it won't fit a long action 700. The underside is contoured to sit flush against the receiver and match the ejection port geometry for a clean, gap-free fit. If you're running a short action 700, it bolts right on with the included hardware.
Why would I want a 20 MOA base instead of a flat one?
The 20 MOA cant tilts your scope forward, which shifts more of your scope's internal elevation toward dialing up for distance. That keeps you from running out of adjustment when you're reaching out past 600 yards. For general close-range work a flat base is fine, but for long-range and precision shooting the 20 MOA gives you room to grow.
Can I still zero at 100 yards with the 20 MOA cant?
In most cases, yes. As long as your scope has a healthy amount of total elevation travel, the forward slope won't stop you from zeroing at 100. The one thing to watch is a scope with a tight elevation range, since the added cant eats into your downward adjustment, so check your optic's specs before ordering.
What scope rings work with this rail?
Any standard Picatinny or Weaver-pattern rings will clamp right onto this rail since it's built to MIL-STD-1913 spec. The full-length slots let you position your rings anywhere along the base to nail down your eye relief. Just match your ring height to your scope's objective diameter and you're set.




Reviews
There are no reviews yet.