Description
If you reload for an 8mm or anything else running a .323 bullet, this Redding Titanium Nitride bushing lets you control neck tension with real precision instead of leaving it up to a one-size-fits-all die. Built from heat treated steel and hand polished to a surface hardness of Rc 60-62, it already slides brass through with ease. The Titanium Nitride coating takes that a step further, bumping up the effective surface hardness and knocking down sizing friction so each stroke feels a little cleaner.
How the .323 TiN Bushing Fits Your Setup
These bushings share the same external dimensions as the rest of the Redding lineup, 1/2 inch O.D. by 3/8 inch long, and freely interchange across all Redding bushing-style neck sizing dies. That means you can keep a few sizes on hand and swap them as your brass or bullet choice changes without buying a whole new die. Each one is clearly marked with its size I.D., so there's no squinting or guesswork when you grab one off the bench.
Picking the Right Bushing Size
The whole point of a bushing system is matching neck tension to your exact brass. The usual method is to measure the outside neck diameter of a loaded round with a micrometer, then subtract .001 to .002 inch to account for brass springback and proper bullet grip. This .323 model fits neatly into the 8mm range, and because Redding offers the full lineup in .001 inch steps from .185 through .368, you can fine-tune tension as tight or as light as your load workup calls for.
Why Handloaders Reach for the TiN Version
The Titanium Nitride treatment is the upgrade over the standard steel bushing. It resists wear, reduces the effort it takes to run a case neck through, and holds up over long reloading sessions. For precision shooters chasing consistent neck tension and better case life, it's a small part that makes a noticeable difference downrange. Made in the USA.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 76323
- UPC: 611760763236
- Bushing Diameter: .323 in
- Bushing Type: Titanium Nitride (TiN) coated
- Construction: Heat treated steel with Titanium Nitride surface treatment
- Surface Hardness: Rc 60-62
- External Dimensions: 1/2 in O.D. x 3/8 in long
- Caliber Range Fit: 8mm (.323)
- Compatibility: All Redding bushing-style neck sizing dies
- Available Size Range: .185 in to .368 in in .001 in increments
- Country of Origin: USA
What’s Included
- One Redding .323 Titanium Nitride neck sizing bushing (76323)
Frequently Asked Questions
What dies does the Redding .323 Titanium Nitride bushing work with?
It freely interchanges in all Redding bushing-style neck sizing dies. Because every bushing in the line shares the same 1/2 inch O.D. by 3/8 inch length, you can swap sizes in and out of the same die as your needs change. The die itself is sold separately.
How do I know if the .323 is the right bushing size for my brass?
Measure the outside neck diameter of a loaded cartridge with a micrometer, then subtract about .001 to .002 inch to allow for brass springback and bullet tension. That number tells you which bushing to run. The .323 lands in the 8mm range, but since neck dimensions vary with brass and neck wall thickness, it's worth confirming with your own measurements.
What's the difference between the Titanium Nitride bushing and the standard steel one?
Both start as heat treated steel hand polished to Rc 60-62 hardness. The Titanium Nitride version adds a TiN surface treatment that raises the effective surface hardness and reduces sizing friction. That translates to smoother sizing strokes and added wear resistance over a lot of reloading cycles.
Will using this bushing help with case life and neck tension consistency?
That's exactly what the bushing system is built for. By choosing the correct bushing you apply just the right amount of neck tension to hold the bullet without over-working the brass. Less excessive resizing means more consistent tension round to round and longer case life.





Reviews
There are no reviews yet.