0
0

Redding Titanium Nitride Neck Sizing Bushing .310 (76310)

UPC: 611760763106

$34.99

5 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

This is the .310 diameter Titanium Nitride neck sizing bushing from Redding, part number 76310. If you run a bushing-style neck sizing or Type S die, this little bronze-colored ring is how you control exactly how much you squeeze down a case neck. Instead of oversizing the neck and dragging it back over an expander like a standard full length die does, a bushing sizes the outside of the neck to precisely where you want it, which means less working of the brass and more consistent bullet tension round to round.

The Titanium Nitride part is what sets these apart from Redding's plain steel bushings. Underneath it's the same heat treated steel, but the TiN surface treatment bumps up the surface hardness and cuts down on sizing friction. The payoff is a smoother stroke and less drag on the neck, which handloaders chasing low runout and repeatable neck tension tend to appreciate.

How the .310 Titanium Nitride Bushing Fits Your Setup

Every Redding bushing shares the same external dimensions, a half-inch outside diameter and three-eighths inch length, so they freely interchange across all Redding bushing-style neck sizing dies. They also swap into L.E. Wilson style dies, which is handy if you run an arbor press setup. The bushing is clearly marked with its size so you're never guessing which one is which when you've got a drawer full of them.

Picking the Right Bushing Size

The quick method is to load a round with the brass and bullet you actually use, measure the loaded neck's outside diameter with a precision micrometer, then subtract .001 to .003 inches for your desired neck tension. Redding's own guidance when you're not neck turning is to go about .002 under and still run the expander. The .310 lands in the 30 caliber range, and since the full TiN lineup covers .185 through .368 in .001 inch steps, it's easy to grab a couple sizes on either side when you're working up a load. One note worth remembering: these bushings aren't stainless, so wipe them down and don't leave one sitting in a die with wet lube.

Key Specifications

  • Manufacturer: Redding
  • Manufacturer Part Number: 76310
  • UPC: 611760763106
  • Bushing Diameter: .310 in
  • Coating: Titanium Nitride (TiN)
  • Base Material: Heat treated steel
  • Outside Diameter: 1/2 in
  • Length: 3/8 in
  • Caliber Range (full line): .185 in – .368 in in .001 in increments
  • Compatibility: Redding bushing-style neck sizing dies and L.E. Wilson style dies
  • Quantity: 1 bushing
  • Country of Origin: United States

What’s Included

  • One (1) Redding .310 Titanium Nitride neck sizing bushing (76310)

Frequently Asked Questions

What dies does the Redding .310 Titanium Nitride bushing fit?

It drops into any Redding bushing-style neck sizing die, including the Type S line. Because every Redding bushing shares the same half-inch outside diameter and three-eighths inch length, they interchange freely across those dies. They also fit L.E. Wilson style dies, which is useful if you run an arbor press.

How do I know if .310 is the right bushing size for my loads?

Load a cartridge with the exact brass and bullet you plan to shoot, then measure the loaded neck's outside diameter with a precision micrometer. Subtract .001 to .003 inches for the neck tension you want, and that's your bushing size. If you aren't neck turning, Redding suggests going about .002 under and still running the expander, so it's smart to keep a size or two on either side of .310 on hand.

What's the difference between the Titanium Nitride bushing and the plain steel one?

Both start as the same heat treated steel, but the Titanium Nitride version adds a TiN surface coating. That coating raises the surface hardness and reduces friction during sizing, giving you a smoother stroke that's a bit easier on your brass. You can tell them apart by the bronze-gold color of the TiN finish.

Does this bushing need an expander, or can I use it on its own?

You can run it with or without the expander depending on how your brass measures and whether you neck turn. Shooters using uniform or turned necks often skip the expander for the straightest results, while those loading mixed-thickness factory brass usually keep the expander in play. The bushing itself controls the outside neck diameter either way.

Additional information

UPC

611760763106

Manufacturer

Manufacturer Part Number

76310

Reviews

There are no reviews yet.

Be the first to review “Redding Titanium Nitride Neck Sizing Bushing .310 (76310)”