Description
This is Redding's .246 diameter neck sizing bushing with a titanium nitride surface treatment, part number 76246. If you run a Type S or Competition bushing die, this little ring is what lets you control exactly how much your case necks get sized, which is the whole point of going the bushing route instead of a standard die. It measures 1/2 inch outside diameter by 3/8 inch long and interchanges freely with all Redding bushing-style sizing dies, along with Wilson-pattern bushings.
Why the TiN Coating on the 76246 Bushing Matters
Underneath, these are heat-treated steel bushings hand-polished to a surface hardness of Rc 60 to 62, which keeps sizing effort low. The titanium nitride treatment goes a step further by boosting that surface hardness and cutting friction during sizing. With a lubed neck, a TiN bushing glides through and tends to leave the brass looking clean. For folks who size a lot of rounds, that slicker surface just makes the whole job feel smoother.
Picking the Right Redding Neck Sizing Bushing Size
The idea behind a bushing die is control. Rather than oversizing the neck and then dragging it back open over an expander, you pick a bushing that sizes the outside of the neck to right where you want it. To find your number, measure the outside neck diameter of a loaded round with a good micrometer, then subtract about .001 to .002 inch to account for brass spring-back and give you proper bullet tension. A lot of handloaders buy the size they calculate plus one on each side so they can fine-tune neck tension as they develop a load.
What the 76246 Fits
Redding offers these bushings in .001 inch increments covering calibers from .17 all the way up to .338, so the .246 slots into that lineup. Each one is marked with its size for easy identification at the bench, and it's made in the USA. Keep in mind dies and shellholders are sold separately, so this is the bushing on its own.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 76246
- UPC: 611760762468
- Bushing Diameter: .246 inch
- Surface Treatment: Titanium Nitride (TiN)
- Material: Heat-treated steel
- Surface Hardness: Rc 60-62
- Dimensions: 1/2 inch O.D. x 3/8 inch long
- Compatibility: All Redding bushing-style dies; interchanges with Wilson-style bushings
- Caliber Range of Series: .17 through .338
- Country of Origin: United States
- Quantity: 1 bushing
What’s Included
- One Redding .246 titanium nitride neck sizing bushing (76246)
Frequently Asked Questions
What die does the Redding .246 bushing fit?
It interchanges freely with all Redding bushing-style sizing dies, including the Type S Full Length, Type S Neck, and Competition Bushing Neck dies. It also works with Wilson-style bushings since it shares the same 1/2 inch outside diameter by 3/8 inch long dimensions. The die itself and the shellholder are sold separately.
How do I know if .246 is the right bushing size for my load?
Measure the outside neck diameter of a loaded round with a precision micrometer, then subtract about .001 to .002 inch to allow for brass spring-back. That number is the bushing you want. If your brass has uneven neck wall thickness, you may need to go a touch smaller and finish with an expander, or neck turn for the most consistent results.
What's the benefit of the titanium nitride version over a plain steel bushing?
The TiN bushing is the same heat-treated steel underneath with the same Rc 60-62 surface hardness, but the titanium nitride coating adds hardness and reduces friction. That means slicker sizing and, with a lubed neck, a cleaner look on the brass. If you size a high volume of rounds, the reduced effort is noticeable.
Will this bushing size my entire case neck?
No, and that's by design. Because of how the die is machined, a bushing leaves a small unsized portion near the shoulder, which is normal and does not hurt accuracy. The bushing controls the outside neck diameter and therefore your neck tension, which is the whole reason to run a bushing setup.




Reviews
There are no reviews yet.