0
0

Redding 73 Style Steel Neck Sizing Bushing .334 – 73334

UPC: 611760733345

$20.99

5 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

Neck tension is one of those little details that separates good handloads from great ones, and a quality bushing is how you control it. This is the Redding 73 Style Steel Bushing in a .334 diameter, machined from heat-treated steel and built to give you precise, repeatable sizing every time you run a case through your die. Instead of over-working the brass with a standard one-pass sizer, a bushing lets you size the neck down just enough to hold the bullet securely, which means longer case life and more consistent results on the target.

What the .334 Redding Bushing Does for Your Loads

The whole idea behind bushing dies is choosing the right neck diameter for your brass and your bullet combination. To find your size, you measure the outside neck diameter of a loaded round with a micrometer and then subtract .001 to .002 inches to allow for brass spring-back and proper bullet grip. That .334 falls into the range used by larger calibers, and because Redding offers these in .001 inch steps, you can fine-tune neck tension without guessing. Running moly-coated bullets? Those sometimes call for a bushing a thousandth or two smaller.

How the 73 Style Steel Bushing Is Built

These bushings aren't just turned and shipped. The sizing surfaces are hand-polished to a surface hardness of Rc 60-62, which cuts down on sizing effort and leaves the case necks clean when you've got them properly lubed. Each one is clearly marked with its size so there's no squinting or second-guessing when you're swapping between a few of them. Dimensionally they share the standard half-inch outside diameter and three-eighths length, so this one freely interchanges across all Redding bushing-style sizing dies.

Built in the USA for Precision Reloaders

Redding has a long reputation among precision and benchrest crowds, and their steel bushings are a big part of why. Made in the USA, this .334 is a smart addition if you're already running a Redding bushing die and want to tune your neck tension to match a new brass lot or bullet. Keep in mind the die and shellholder are separate, so grab one if you don't already have the setup.

Key Specifications

  • Manufacturer: Redding
  • Manufacturer Part Number: 73334
  • UPC: 611760733345
  • Type: Neck Sizing Die Bushing
  • Diameter: .334 in
  • Material: Heat-Treated Steel
  • Surface Hardness: Rc 60-62
  • Outside Dimensions: 1/2 in O.D. x 3/8 in long
  • Compatibility: All Redding bushing-style sizing dies
  • Country of Origin: United States

What’s Included

  • One Redding 73 Style Steel Neck Sizing Bushing, .334 diameter

Frequently Asked Questions

How do I know if the .334 Redding bushing is the right size for my brass?

Measure the outside neck diameter of a loaded cartridge with a precision micrometer, then subtract .001 to .002 inches. That gives you the correct bushing size to allow for brass spring-back and proper bullet tension. If you're loading moly-coated bullets, you may want to go a thousandth or two smaller.

Will this bushing work in my Redding die?

Yes. These 73 style steel bushings freely interchange in all Redding bushing-style neck sizing dies. They use the standard half-inch outside diameter and three-eighths inch length, so you can swap sizes in the same die as your needs change.

What's the difference between the steel bushing and the Titanium Nitride version?

This is the heat-treated steel version, hand-polished to a surface hardness of Rc 60-62 to keep sizing effort low. The Titanium Nitride bushings add a surface treatment that increases hardness further and reduces sizing friction a bit more. Both interchange in the same dies, so it comes down to preference and budget.

Does this come with a die or shellholder?

No, this is the bushing only. The sizing die and shellholder are sold separately, so you'll want a Redding bushing-style die already in your setup to use it. It's a great way to add or fine-tune neck tension without buying a whole new die.

Additional information

UPC

611760733345

Manufacturer

Manufacturer Part Number

73334

Reviews

There are no reviews yet.

Be the first to review “Redding 73 Style Steel Neck Sizing Bushing .334 – 73334”