Description
Neck tension is one of those details that separates good handloads from great ones, and a quality bushing is how you take control of it. This is the Redding .260" heat-treated steel neck sizing bushing, part number 73260, machined to tight tolerances so you can size your case necks down just enough to hold a bullet securely without overworking the brass. Less overworking means longer case life and more consistent seating from round to round.
The sizing diameter is hand-polished to a surface hardness of Rc 60-62, which cuts down on sizing effort and keeps the finish smooth where it matters. Like the rest of Redding's bushing lineup, this one carries the same external dimensions as the whole range (1/2" O.D. by 3/8" long), so it freely interchanges across all Redding bushing-style neck sizing and Type S dies. Each bushing is clearly marked with its I.D. so you always know which one you've got in hand.
Picking the Right .260 Bushing for Your Brass
Sizing is specific to your chamber and your brass, so the best way to land on the correct bushing is to measure the outside neck diameter of a loaded cartridge with a precision micrometer, then subtract about .001". That gives you the neck tension needed to grip the bullet while letting the brass spring back naturally. If you're running moly-coated bullets, you may want to go a touch smaller. Keep in mind Redding, Hornady, RCBS, Short Action Customs and Wilson bushings all share the same footprint and interchange freely.
Where the 73260 Steel Bushing Earns Its Keep
This .260" size is a common pick for 6.5mm and 25-caliber loads, and it's a favorite among precision and benchrest reloaders who want to fine-tune neck tension rather than leave it to a one-size button. Steel bushings like this one are a great value if you're building out a set across several thousandths so you can experiment and find what your rifle likes best. Made in the USA.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 73260
- UPC: 611760732607
- Bushing Diameter: .260 inch
- Material: Heat-Treated Steel
- Surface Hardness: Rc 60-62, hand polished
- External Dimensions: 1/2" O.D. x 3/8" long
- Style: 73 Style Bushing-Type Neck Sizing
- Compatibility: All Redding bushing-style and Type S dies
- Country of Origin: USA
What’s Included
- One Redding .260" heat-treated steel neck sizing bushing (73260)
Frequently Asked Questions
What size bushing do I need for my .260 loads?
The right size depends on your brass and chamber, not just the caliber. Measure the outside neck diameter of a loaded cartridge with a precision micrometer and subtract about .001" to find your starting point. This .260" bushing is a common fit for many 6.5mm and 25-caliber loads, but always confirm against your own measured brass.
Will this Redding steel bushing fit my die?
Yes, it uses the standard external dimensions of 1/2" O.D. by 3/8" long and freely interchanges across all Redding bushing-style neck sizing and Type S dies. It's also interchangeable with Hornady, RCBS, Short Action Customs and Wilson bushings since they share the same footprint. Dies and shellholders are sold separately.
What's the difference between the steel and titanium nitride versions?
This is the heat-treated steel bushing, part number 73260. Both the steel and the titanium nitride versions share the same dimensions and do the same job, but the TiN coating adds extra surface hardness and reduces sizing friction. The steel bushing is the more budget-friendly way to build out a range of sizes for load development.
Should I size down more for moly-coated bullets?
Yes, moly-coated bullets often call for a slightly tighter neck. In those cases you may want a bushing .001" or .002" smaller than what you'd choose for bare bullets. It's worth testing a couple of sizes to see what grips best in your setup.




Reviews
There are no reviews yet.