Description
If you're casting your own pistol bullets for 10mm Auto or .40 S&W, this RCBS mould drops a classic 200-grain semi-wadcutter at .400" diameter. The semi-wadcutter profile is a proven performer for target work and general range shooting, cutting clean holes in paper while feeding well through most magazines. With two cavities, you'll pour two bullets at a time, which keeps a casting session moving once the blocks come up to temperature.
What Sets the RCBS 10mm-200-SWC Mould Apart
RCBS builds these moulds from solid cast iron blocks, machined to tight tolerances so you get consistent weight and diameter from the first pour to the thousandth. The blocks are precision ground square before machining, and hardened steel alignment pins keep both halves mating perfectly even after years of heavy use. That attention to fit is what keeps your bullets concentric and your weights uniform.
Built to Pour Session After Session
Up top you'll find a 3/16-inch solid steel sprue plate held in place with tempered steel spring washers and screws. That thick plate holds heat and gives you a clean, square cut on the bullet base every time you swing it open. This is a plain base semi-wadcutter design, so there's no gas check shank to fuss with, which keeps your casting and sizing routine simple.
Getting the Most From Your RCBS Bullet Mould
RCBS spec'd their pistol moulds around an alloy of 10 parts lead to 1 part tin, which casts a reasonably hard bullet that fills out the cavities nicely and delivers good accuracy. One thing worth knowing before your first pour: the mould handles are sold separately, so make sure you've got a set on the bench. Pair it with a .400" sizer and the #518 top punch to size and lube your finished bullets, and you'll have a steady supply of 200-grain SWCs ready for the loading press.
Key Specifications
- Manufacturer: RCBS
- Mould Number: 10mm-200-SWC
- Manufacturer Part Number: 82068
- UPC: 076683820686
- Bullet Diameter: .400" (.401)
- Bullet Weight: 200 Grain
- Bullet Style: Semi-Wadcutter (SWC)
- Cartridges: 10mm Auto, .40 S&W
- Cavity Count: 2 (Double Cavity)
- Gas Check: No (Plain Base)
- Block Material: Solid Cast Iron
- Sprue Plate: 3/16" Solid Steel
- Sizer / Top Punch: .400" Sizer, #518 Top Punch
- Country of Origin: USA
What’s Included
- RCBS 10mm-200-SWC two-cavity bullet mould block
- 3/16" solid steel sprue plate with mounting hardware (spring washers and screws)
Frequently Asked Questions
Do the mould handles come with the RCBS 10mm-200-SWC mould?
No, the handles are sold separately. RCBS designs their mould blocks to work with their standard handle set, so you'll want to grab a pair if you don't already have them on your bench. Once you've got handles attached, the blocks drop right in and you're ready to cast.
What cartridges will these .400" 200-grain bullets work in?
This mould casts bullets at .400"/.401" diameter, which makes them a natural fit for 10mm Auto and .40 S&W. The 200-grain semi-wadcutter is a popular all-around weight for target and range shooting in both calibers. As always, work up your loads from published data for the bullet weight and cartridge you're running.
Does the RCBS 10mm-200-SWC mould require a gas check?
No, this is a plain base semi-wadcutter design with no gas check shank. That keeps your casting and sizing process simple since there's no check to seat during sizing. For typical pistol velocities with a properly hard alloy and good lube, a plain base bullet does the job well.
What alloy does RCBS recommend for this mould?
RCBS set up their pistol moulds using an alloy of 10 parts lead to 1 part tin. That mix casts a reasonably hard bullet that fills out the cavities cleanly and holds accuracy. It's also inexpensive and easy to source, which is why RCBS adopted it as their pistol standard.





Reviews
There are no reviews yet.