Description
Case lube is one of the biggest hassles in pistol reloading, and this is the die that lets you skip it entirely. The RCBS Carbide Sizer Die resizes straight-wall 9mm cases and punches the spent primer in a single stroke, thanks to a tungsten carbide insert pressed into the body. That carbide ring is so slick you load dry brass straight into the press, no wiping, no spray, no sticky mess to clean off afterward.
What the RCBS Carbide Sizer Die Actually Does
This is the sizing and decapping half of the reloading process in one tool. Drop a case in the shellholder, run it up, and the die squeezes it back to spec while the decapping stem pushes out the old primer. It's cut for both 9mm Luger and 9×21, so if you're running either cartridge it covers you. The die body is hardened with a non-slip lock ring, and the expander-decapping assembly threads in and locks down so it holds its adjustment stroke after stroke.
Why Reloaders Reach for the RCBS Carbide 9mm Sizer
RCBS holds tighter tolerances on their sizing dies than you'll find on most factory chambers, which is a big part of why reloaded rounds chamber so smoothly round after round. The carbide insert also lasts a very long time compared to plain steel, so this is the kind of die you buy once and keep running for years. Buying the sizer by itself is handy when you already have a seating and crimp setup, or when you just want a dedicated carbide sizer without springing for a full set.
Setup Notes for the RCBS Carbide Sizer Die
A quick heads up on setup: with carbide dies you thread the die down until it just kisses the shellholder at the top of the stroke, then lock it, rather than camming it hard over. Set the decapping pin so it sticks out roughly 3/16 inch below the die to pop primers cleanly. The shellholder is sold separately, so grab the correct one for 9mm if you don't already have it on the bench.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number: 20537
- UPC: 076683205377
- Caliber: 9mm Luger / 9×21
- Die Type: Carbide Sizer Die
- Function: Sizes and decaps in one step
- Insert: Diamond-lapped tungsten carbide ring
- Case Lube Required: No
- Thread Size: 7/8-14
- Dies In Set: 1
- Shipping Weight: 0.7 lb
- Warranty: RCBS Lifetime Guarantee
What’s Included
- Carbide sizer die body with tungsten carbide insert
- Decapping stem and pin assembly
- Die lock ring
- Printed instruction manual
- Reloading data sticker
- Gray RCBS plastic storage box
Frequently Asked Questions
Does the RCBS Carbide Sizer Die need case lube?
No. The tungsten carbide ring inside the die is polished smooth enough that you can run clean, dry 9mm brass straight into it. That saves you the lubing and wiping-down steps that steel sizing dies require.
Is a shellholder included with this 9mm sizer die?
No, the shellholder is sold separately. You'll need the correct RCBS shellholder for 9mm Luger to hold the case in your press. If you already reload 9mm or 38 Super on an RCBS setup, there's a good chance you already own the right one.
Can I use the RCBS Carbide Sizer Die for 9×21 as well as 9mm Luger?
Yes. This die is cut for both 9mm Luger and 9×21, so one tool covers both cartridges. The carbide insert resizes the straight-wall case and deprimes it in the same stroke for either one.
Does this die replace a full 3-die set?
Not on its own. This is the sizing and decapping die only, so you'll still need an expander and a seating or crimp die to finish loading a round. It's a great pick when you want a standalone carbide sizer or a replacement for a set that didn't come with one.



Reviews
There are no reviews yet.