Description
The RCBS Full-Length Die Set in .35 Remington is a classic two-die setup built for reloading bottleneck cases on a standard single-stage press. It covers the two jobs that matter most for this cartridge: bringing fired brass back down to spec and seating your bullet clean and straight. The sizer die includes an expander-decapping unit, so in one stroke you resize the outside of the case, punch out the spent primer, and open the neck back up to accept a fresh bullet. The seater die handles the second half with a bullet seater plug and a built-in roll crimp that locks the bullet in place as it's seated.
Why the RCBS .35 Remington Sizer Is Built the Way It Is
Full-length sizing is the way to go for the .35 Remington, especially if you're feeding a Marlin 336 or another lever or pump gun. Resizing the whole case means every round drops in and cycles without fighting the action. The sizer brings brass down to SAAMI minimum dimensions while holding headspace to tight tolerances so you're not stretching the case body during the process. There are vent holes machined into the die to let trapped air and excess lube escape, which keeps you from dinging or denting a case while you work.
Getting the Most From This RCBS Two-Die Set
The .35 Remington has thin case necks that can buckle if you rush the sizing stroke, so go slow and keep your lube consistent. Seating depth on this cartridge is usually dialed in off the bullet's cannelure, and the built-in roll crimp is a real plus for tubular magazine rifles where recoil can shove bullets deeper if they aren't held tight. These dies use standard 7/8-14 threads, so they'll thread into any common press. One thing worth knowing up front: you'll need an RCBS #9 shell holder to run this set, and that's sold separately. RCBS has been turning out reloading gear for decades, and this set carries the same reputation for fit and longevity that handloaders have come to expect.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number: 16501
- UPC: 076683165015
- Model: Full-Length 2-Die Set
- Caliber: .35 Remington
- Die Type: Full Length Sizer / Seater
- Number of Dies: 2
- Series: Group A
- Thread: 7/8-14 TPI (standard)
- Carbide: No
- Crimp: Built-in roll crimp
- Shell Holder: Uses RCBS #9 (sold separately)
- Case Type: Bottleneck rifle
What’s Included
- Full-length sizer die with expander-decapping unit
- Seater die with bullet seater plug and built-in roll crimp
Frequently Asked Questions
Does the RCBS .35 Remington die set come with a shell holder?
No, the shell holder is not included with this set. You'll need an RCBS #9 shell holder to run these dies, and it's sold separately. It's an inexpensive add-on, so it's worth grabbing one at the same time if you don't already have it.
Is full-length sizing the right choice for a lever-action .35 Remington?
Yes, full-length sizing is the preferred method for lever and pump guns like the Marlin 336. Resizing the entire case ensures every round chambers, feeds, and extracts smoothly without binding. The sizer also holds headspace to minimum tolerances to keep things consistent from one load to the next.
Do these dies have a crimp built in?
Yes, the seater die includes a built-in roll crimp that secures the bullet at the same time it's seated. That's a handy feature for the .35 Remington since tubular magazine rifles can push bullets deeper under recoil if they aren't crimped tight. Seating depth is typically set off the cannelure on your chosen bullet.
Will this RCBS die set fit my press?
It should. The set uses standard 7/8-14 threads, which is the common standard for single-stage and turret presses from most major brands. If your press accepts standard dies, these will thread right in.




Reviews
There are no reviews yet.