Description
If your 1911 is experiencing loose extraction or inconsistent ejection patterns, the root cause often traces back to an undersized or poorly fitting factory firing pin stop. The EGW oversized version solves this problem at its source by providing a wider and thicker component that anchors the extractor in proper position while the gun cycles.
This particular stop fits Series 70 1911s chambered in 9mm, .38 Super, and .40 S&W, and it's specifically machined with a cut across the top to clear Bomar-style rear sight dovetails. That means it integrates cleanly into setups where rear sights might otherwise interfere. The blue finish matches standard blued slides and frames.
What Makes This Oversized Stop Different
EGW machines this part wider than a standard GI-spec firing pin stop to physically prevent the extractor from turning inside the slide. It's also thicker than factory parts, which eliminates side-to-side movement during recoil. These two design characteristics work together to stabilize ejection and improve overall reliability. The inside corners are radiused to prevent cracking under hard use, extending the service life of the part through thousands of rounds.
The rear corner features a carefully engineered .015-inch radius that breaks the sharp edge while maintaining a square profile. This geometry slows the slide's initial opening just enough to reduce felt recoil and battering without sacrificing the gun's timing or functionality. That controlled slide velocity translates to less perceived kick and better follow-up shot capability.
Hardness and Durability
Rockwell tested to 48 Rc on the hardness scale, this firing pin stop resists peening and deformation that can occur over high round counts. The hardened carbon steel construction ensures it holds its shape and continues controlling the extractor properly even after extended use. It's a small part that handles serious shooting demands.
Installation Note
This is not a drop-in component. Because it's intentionally oversized, fitting is required to lock it tightly into the slide. That extra material allows you to precisely match your specific slide while gaining all the performance benefits EGW designed into it. Most builders and experienced shooters handle this work themselves, though a qualified gunsmith can perform the fitting if needed. Series 70 firing pin stops only work in Series 70 pistols and will not fit Series 80 models without modification.
Key Specifications
- Manufacturer: Evolution Gun Works (EGW)
- Model Number: 10375
- UPC: 841370116249
- Caliber: 9mm, .38 Super, .40 S&W
- Series: Series 70
- Material: Carbon Steel
- Finish: Blue
- Rear Sight Cut: Bomar-style (adjustable sight cut)
- Hardness: 48 Rockwell C
- Rear Corner Radius: .015 inch
- Drop-In Installation: No, requires custom fitting
- Design Type: Oversized, flat bottom
What’s Included
- 1x EGW Oversized Firing Pin Stop Series 70 (9/38/40, Blue)
Frequently Asked Questions
Will this firing pin stop fit my Series 80 1911?
No. This is designed specifically for Series 70 pistols and will not fit Series 80 models without modification. Series 80 firing pin stops will work in Series 70 guns, but Series 70 stops are series-specific. Always verify your 1911's series before purchasing.
Does this firing pin stop require fitting, or is it drop-in?
This part requires fitting. Because it's intentionally oversized, you'll need to sand or file it to match your specific slide. The extra material gives you precision control to achieve a snug, custom fit that delivers all the performance benefits. Most experienced builders handle this themselves, though a gunsmith can fit it for you.
What performance improvement should I expect from this firing pin stop?
The wider profile prevents your extractor from rotating, which means more consistent and reliable case ejection. The thicker design eliminates lateral movement during cycling, so the gun runs smoother. The flat bottom geometry with the rear radius slows slide opening slightly to reduce felt recoil and muzzle flip while improving follow-up shot speed.
Is this compatible with my Bomar-style rear sight?
Yes. This model is specifically cut across the top to clear Bomar-style rear sight dovetails, so it integrates cleanly into setups with adjustable rear sights that would otherwise interfere with a standard firing pin stop.





Reviews
There are no reviews yet.