Description
The EGW Mossberg 695 Bolt Action rail is a one-piece Picatinny base built to turn your 695 slug gun into a serious optics-ready setup. It drops onto the factory receiver holes using the included hardware, so there's no drilling, no tapping, and no gunsmith appointment. If you've been running your 695 on open sights and want to hang a real scope or red dot on it, this is the clean way to get there.
Why the Mossberg 695 Rail Earns Its Keep
EGW machines this base from domestic 6061 T6 extruded aluminum and finishes it in a matte black Type II anodizing, so it shrugs off the knocks and weather that come with slug season. It's cut to the MIL-STD 1913 Picatinny spec, which means it plays nice with both Picatinny and Weaver rings. The whole thing weighs in around 2 ounces and sits roughly 0.575 inches from the top of the receiver to the top of the rail, keeping your optic low and your cheek weld comfortable.
Dialing In Your Mossberg 695 Optic
This is a 0 MOA base, which is the right call for the ranges a 695 slug gun actually works at. Zero MOA keeps your scope's adjustment travel centered for shooting inside a few hundred yards, where most deer and bear hunters are taking their shots. The extended overall length of 6.276 inches gives you plenty of room to slide your rings fore and aft to get eye relief sorted for your particular scope and shooting position.
Built Ambidextrous and Simple to Install
EGW beveled both sides of the base, so lefties and righties both get a clean, snag-free profile. Installation is straightforward: EGW recommends about 20 inch-pounds of torque and a drip of blue thread locker on the screws to keep everything locked down under recoil. Before you order, it's worth measuring the hole spacing on your receiver to confirm it matches the 3.805-inch center spread EGW publishes, just so you know you're getting the right fit the first time.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- MPN / Part Number: 45400
- UPC: 841370106356
- Fits: Mossberg 695 Bolt Action Shotgun
- Rail Type: One-Piece Picatinny (MIL-STD 1913)
- Minute of Angle: 0 MOA
- Material: Domestic 6061 T6 Extruded Aluminum
- Finish: Matte Black Type II Anodizing
- Center Spread: 3.805 in
- Overall Length: 6.276 in
- Height: 0.575 in (receiver top to rail top)
- Weight: 2 oz
- Ambidextrous: Yes (beveled both sides)
- Ring Compatibility: Picatinny and Weaver rings
- Quick Disconnect Ring Compatible: No
- Made In: USA
What’s Included
- EGW Mossberg 695 one-piece Picatinny rail base
- #6-48 x 1/4 mounting screws
- T-10 bit
Frequently Asked Questions
Does the EGW Mossberg 695 rail require drilling or tapping?
No. This base mounts to the existing receiver holes on your Mossberg 695 using the included #6-48 screws, so there's no drilling or tapping needed. EGW recommends torquing the screws to about 20 inch-pounds and adding a drop of blue thread locker so everything stays put under slug recoil.
What scope rings work with this Mossberg 695 Picatinny rail?
The base is cut to the MIL-STD 1913 Picatinny spec, so it accepts both Picatinny and Weaver-style rings. One thing to note is that it is not compatible with quick-disconnect rings, so plan on a standard clamp-style ring set.
Why is this a 0 MOA rail instead of 20 MOA?
A 0 MOA base keeps your scope's elevation adjustment centered, which is ideal for the shorter ranges a 695 slug gun is used at. EGW recommends 0 MOA for shooting inside roughly 500 yards, which covers just about any realistic shot you'd take with this shotgun.
How do I make sure the rail fits my Mossberg 695 before ordering?
This mount is built specifically for the Mossberg 695 bolt action shotgun with a 3.805-inch center spread. EGW recommends measuring the center-to-center distance between the two middle receiver holes to confirm it matches that published spacing, so you know it'll line up before installation.




Reviews
There are no reviews yet.