Description
The EGW Marlin 39 Picatinny Rail is a one-piece scope base built specifically for the Marlin 39 and 39A lever-action rimfire rifles. It bolts to the factory scope mount holes on your receiver and gives you a modern Picatinny platform to run just about any rings and optic you want. If you've been trying to scope one of these classic lever guns and fighting with short or oddly placed bases, this is the kind of mount that solves the problem.
What Makes the Marlin 39 Rail Tick
EGW machines this base from domestic 6061 T6 extruded aluminum and finishes it in a matte black Type II anodizing, so it holds up to real field use and matches the look of a traditional blued rifle. It runs about 4 inches long, sits roughly 0.4 inches above the receiver, and tips the scale at around 2 ounces, so you get a sturdy base without piling on weight. A milled channel down the center knocks off extra mass and, in a lot of cases, still leaves your factory iron sights usable.
Dialing In Your Optic
The full-length cross slots are cut to MIL-STD 1913 spec within a couple thousandths, which means you can slide your rings fore and aft to nail down proper eye relief instead of being locked into one position. It accepts both Picatinny and Weaver style rings, so you aren't boxed into a single ring brand. This is the 0 MOA version, which is the right call for the close-to-mid range work a .22 lever gun is built for.
Mounting the Marlin 39A Base
The rail is ambidextrous and ships ready to install with the correct screws and a Torx bit in the box. EGW recommends torquing the screws to 20 inch-pounds with a drop of blue Loctite to keep everything locked down under recoil. Because the 39A receiver profile changed over the decades, it's smart to measure your receiver hole spacing against EGW's published dimensions before you start, so you know you've got the right fit for your particular rifle.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 47310
- UPC: 841370106974
- Fits: Marlin 39 / 39A
- Mount Type: One-Piece Picatinny Rail
- Elevation / Cant: 0 MOA
- Material: 6061 T6 Extruded Aluminum
- Finish: Matte Black Type II Anodized
- Overall Length: 4.00 in
- Height: 0.4 in (receiver top to rail top)
- Center Spread: 1.995 in
- Weight: 2 oz
- Ring Compatibility: Picatinny or Weaver rings
- Ambidextrous: Yes
- Torque Spec: 20 in-lbs
- Country of Origin: USA
What’s Included
- EGW Marlin 39 one-piece Picatinny scope base (1)
- Mounting screws
- Torx bit / wrench
Frequently Asked Questions
Will this EGW rail fit my Marlin 39A?
It's designed for the Marlin 39 and 39A and bolts to the factory scope mount holes. Keep in mind the 39A receiver profile changed over the years, so EGW recommends measuring your receiver's hole spacing against their published dimensions before installing. Some older or variant receivers may need minor fitment work at the rounded front edge.
What does 0 MOA mean on the Marlin 39 mount?
0 MOA means the rail sits perfectly level with no built-in forward cant. That's the right choice for the close-to-mid range shooting a .22 lever gun is made for, giving you plenty of adjustment range in your scope. A canted base is really only needed for long-range centerfire work.
What rings does the Marlin 39 Picatinny rail use?
The cross slots are cut to MIL-STD 1913 Picatinny spec, so it accepts both Picatinny and standard Weaver style rings. The full-length slots let you slide the rings forward or back to set your eye relief. Note it is not quick-disconnect ring compatible.
Can I still use my iron sights with this base installed?
The milled center channel is designed so that in many cases it won't block your factory iron sights. That said, it depends on your specific rear sight setup, since folding rear leaves tend to clear the best. If running irons under the rail matters to you, check your particular sight before mounting.





Reviews
There are no reviews yet.