Description
The EGW Marlin 1894 Picatinny Rail in 0 MOA is the clean, no-nonsense way to get a scope, red dot, or whatever glass you prefer riding on top of your 1894. EGW machines these in-house from domestic 6061 T6 extruded aluminum, then tumbles, sandblasts, and Type II anodizes them in matte black for a finish that holds up to real use. At roughly 2 ounces and sitting about 0.4 inches above the receiver, it adds almost nothing to the gun while giving you a full-length Picatinny platform to work with. This is the undrilled version (part number 47200-U), which means the rail ships without the mounting holes cut, so you or your gunsmith will need to drill and tap it to match your receiver.
Why the Undrilled 1894 Rail Makes Sense
Going with the undrilled base gives you the freedom to line everything up exactly to your particular receiver rather than relying on pre-cut holes. The center spread measures 1.872 inches and overall length runs 4.7 inches, which is the correct geometry for the Marlin 1894. EGW even recommends measuring your receiver's hole spacing against those published numbers before you start, which is smart practice on any older or well-worn lever gun.
Picatinny Flexibility on a Classic Lever Gun
The cross slots run the full length of the rail, so you have real room to slide rings fore and aft and dial in proper eye relief. It accepts both Picatinny and Weaver style rings, which means you are not boxed into one brand of hardware. The 0 MOA elevation is the right call for typical lever gun work inside a few hundred yards, keeping your optic on a flat plane with no built-in cant. In a lot of setups it will also leave your factory iron sights usable underneath.
Built in the USA
EGW makes the whole package stateside, right down to the mounting screws and packaging. The mount includes #8-40 by 1/4 inch screws and a T-10 bit, and EGW suggests torquing to 20 inch pounds with a drip of blue thread locker for a setup that stays put through recoil.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 47200-U
- UPC: 841370106936
- Fits: Marlin 1894
- Rail Type: One-Piece Picatinny
- Elevation: 0 MOA
- Material: Domestic 6061 T6 Extruded Aluminum
- Finish: Matte Black Type II Anodized
- Center Spread: 1.872 in
- Overall Length: 4.7 in
- Height: 0.4 in (top of receiver to top of Picatinny)
- Weight: 2 oz
- Ring Compatibility: Picatinny or Weaver
- Ambidextrous: Yes
- Drilling: Undrilled (requires drilling and tapping)
- Torque Spec: 20 in/lbs
What’s Included
- Marlin 1894 Picatinny rail base (undrilled)
- #8-40 x 1/4 in socket head Torx screws
- T-10 bit
Frequently Asked Questions
What does undrilled mean on the EGW Marlin 1894 rail?
The undrilled version (47200-U) ships without the mounting holes already cut into the rail. That means you or a gunsmith will need to drill and tap it to match your receiver's hole spacing. It gives you precise alignment control, but it is more involved than a pre-drilled base, so plan accordingly if you are not comfortable doing the work yourself.
Will this EGW Picatinny rail fit my older Marlin 1894?
It is designed specifically for the Marlin 1894 with a 1.872 inch center spread and 4.7 inch overall length. EGW recommends measuring the hole spacing on your receiver against those published dimensions before mounting, which is especially worth doing on vintage or heavily used rifles. Many owners of older 1894s report a clean fit once everything lines up.
Does the 0 MOA rail work for both scopes and red dots?
Yes. The full-length Picatinny cross slots let you position rings or a red dot anywhere along the rail to dial in eye relief. It accepts both Picatinny and Weaver style rings, so it handles traditional tube scopes and modern red dots alike.
What hardware comes with the Marlin 1894 rail and how should I install it?
The mount includes #8-40 by 1/4 inch screws and a T-10 bit. EGW recommends torquing the screws to 20 inch pounds and adding a drip of blue thread locker so things stay tight under recoil. Keep in mind the undrilled base still needs to be drilled and tapped to your receiver before final installation.





Reviews
There are no reviews yet.