Description
Swapping gear on and off a rail usually means fighting with a lever, cross bolts, or a torque wrench, and hoping nothing shifted when you're done. Magne-Tech built this locking magnetic mount set to skip all of that. It's a two-piece system, a male rail mount that bolts to your Picatinny rail and a female accessory mount that attaches to whatever you're running, and the two halves snap together with rare-earth magnets the instant they get close to each other.
What's Inside the Lock-In Pic Accessory Mount Set
Both halves are machined from 7075-T6 aluminum and finished with a MIL-A-8625 Type III hard coat anodize, so they're built to shrug off recoil and rough handling rather than just look tough on a shelf. The magnets themselves are nickel-coated and rated for serious holding strength, and once the two pieces mate up, a dual-redundant locking mechanism, a lever plus a set screw, clamps them together so there's no chance of an accidental separation mid-use.
Holding Zero Every Time You Reattach
The real selling point of this accessory mount set is what happens after you take something off and put it back on. Magne-Tech designed the geometry so zero shift stays repeatable within 0.25 MOA, and the set only adds about 0.8 inch of height over the rail, which keeps your setup from getting too tall. It's been run through lab testing that included over a thousand rounds of simulated 5.56 recoil without the mount losing its return-to-zero performance.
Why This Mount Set Earns a Spot on Your Rail
Because it's a universal Picatinny interface, this locking magnetic mount set isn't locked into one specific use. Run it with a red dot, a magnifier, a weapon light, a laser, or a night vision unit, and move that same accessory between rifles without re-zeroing each time. For anyone who's tired of loosening rings or fumbling with QD levers in the field, this is a genuinely different way to manage gear on a rail.
Key Specifications
- Manufacturer: Magne-Tech
- Manufacturer Part Number: MGN-LOCK-PIC-ACC-SET
- UPC: 787790968566
- Mount Configuration: Locking magnetic Picatinny rail mount (male) and accessory mount (female)
- Material: 7075-T6 aluminum alloy
- Finish: MIL-A-8625 Type III hard coat anodized
- Magnet Type: Rare-earth, nickel-coated
- Locking Mechanism: Dual-redundant lever and set screw lock
- Zero Retention: Repeatable within 0.25 MOA after detach and reattach
- Rail Compatibility: MIL-STD-1913 Picatinny
- Added Height: Approximately 0.8 inch above the rail
- Country of Origin: Made in the USA
What’s Included
- Magnetic Picatinny rail mount (male)
- Magnetic accessory mount (female)
- Mounting hardware for rail installation
Frequently Asked Questions
Can I use this locking magnetic mount set with a scope, or just smaller accessories?
It's designed as a universal Picatinny interface, so it works with anything that has a compatible attachment point, including red dots, lights, lasers, night vision, and yes, scopes. Just keep in mind heavier or taller optics may do better with a second mount set for extra support.
Does taking an accessory off and putting it back on affect my zero?
That's the whole point of the design. The magnetic connection combined with the dual-redundant lock keeps the return to zero repeatable within 0.25 MOA, so you're not re-zeroing every time you swap gear.
How much height does this mount set add to my rail?
The set raises your accessory about 0.8 inch above the Picatinny rail. That's worth factoring in if you're running a low-profile setup or need specific eye relief for an optic.
Will this hold up on a hard-recoiling rifle?
It's built from 7075-T6 aluminum with a hard coat anodized finish, and the mount has been tested through over a thousand rounds of simulated heavy recoil without losing its zero retention. It's rated to handle everything from an AR-15 up to harder-kicking AR-10s and bolt guns.



Reviews
There are no reviews yet.