Description
The Lee Wadcutter Pistol Mould is a six-cavity aluminum block that casts a .358 diameter, 148 grain full wadcutter bullet. That flat-nosed profile is the classic paper puncher, cutting crisp, clean holes in targets and making scoring a whole lot easier. It drops bullets sized right for a handful of popular revolver cartridges, so it earns its keep on the bench for anyone shooting a lot of .38 and .357.
What the Lee 6-Cavity .358 148gr Wadcutter Mould Feeds
This block produces bullets suited for .38 Special, .357 Magnum, .38 S&W, and .38 Colt New Police. The bullet runs about .577 inches overall, with a short .105 inches from the crimp groove to the nose. It's a design that's been a bullseye and target-shooting staple for decades, and it's a great match for soft, accurate light-recoil loads you can shoot all day.
How the Lee Wadcutter Mould Is Built
Lee machines these six-cavity blocks from aluminum, which keeps things light and rust-free while heating up and cooling down faster than iron or steel. Less weight also means less hand fatigue during a long casting session. The mold halves are bored for roundness and size control, and they ride on steel bushings and alignment pins for solid, repeatable lockup cast after cast. Up top you get a cam-operated, hard-anodized sprue plate held down by wave washers at each end, so starting the cut on all six sprues takes far less effort than hammering on an ordinary mold.
A Few Things to Know Before You Cast
Handles and mold lube are sold separately on this one, so plan to pair it with a set of Lee six-cavity handles if you don't already have them. Aluminum is a little softer than steel, so a light coat of sprue plate lube on the pivot points and block tops keeps everything running smooth for the long haul. Do that and this mould will put out consistent wadcutters for years.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90380
- UPC: 734307903800
- Bullet Diameter: .358 inch
- Bullet Weight: 148 Grain
- Bullet Style: Wadcutter (WC)
- Number of Cavities: 6
- Block Material: Machined Aluminum
- Sprue Plate: Cam-operated, hard anodized
- Compatible Cartridges: .38 Special, .357 Magnum, .38 S&W, .38 Colt New Police
- Bullet Overall Length: .577 inch
- Crimp Groove to Nose: .105 inch
- Country of Manufacture: United States
What’s Included
- Lee 6-cavity wadcutter mould block (.358 148gr WC)
- Cam-operated hard anodized sprue plate
- Molded storage case
Frequently Asked Questions
Do handles come with the Lee 6-cavity wadcutter mould?
No, handles are sold separately on this mould. You'll want a set of Lee six-cavity mold handles to open and close the block while casting. Mold lube is also sold separately.
What cartridges will the .358 148gr wadcutter work in?
This bullet is sized at .358 diameter and works for .38 Special, .357 Magnum, .38 S&W, and .38 Colt New Police. The 148 grain full wadcutter is a classic target load, especially popular for light-recoil .38 Special bullseye shooting.
Why choose the aluminum six-cavity block over a smaller mould?
Aluminum heats and cools faster than iron or steel and weighs about a third as much, so you get good bullets quickly with less arm fatigue. The six-cavity design lets you drop six bullets per pour instead of one or two, which makes a real difference when you're casting in volume.
Does this mould need any care to keep running well?
A little maintenance goes a long way. Since aluminum is softer than steel, lightly lube the sprue plate pivot, retaining screw, and the tops of the mold blocks with a quality sprue plate lube. Keep those contact points oiled and the mould will give you years of consistent service.





Reviews
There are no reviews yet.