0
0

Lee 358-148-WC Double Cavity Wadcutter Bullet Mould .358 148 gr

UPC: 734307903121

$33.99

2 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

The Lee 358-148-WC double cavity mould is built for folks who want clean, flat-faced wadcutters without paying boxed-bullet prices. It drops two .358 diameter, 148 grain wadcutter bullets per pour, which cuts your casting time roughly in half compared to a single cavity block. The wadcutter profile is a target shooter's favorite because that sharp, full-diameter nose punches clean round holes in paper, making scoring easy at the range or in bullseye matches.

This mould produces bullets suited for .38 Special, .357 Magnum, .38 S&W, and .38 Colt New Police. The finished bullet runs an overall length of .577 inches with the crimp groove sitting .105 inches back from the nose, so seating and crimping stay consistent load after load. Range scrap and wheel weight alloys tend to drop these right around 148 grains and a hair over .358, which is exactly what you want for standard .38 revolvers.

Why Casters Reach for the Lee 358-148-WC Mould

Lee machines the blocks from aluminum for good reason. The material won't rust, it heats up and cools down faster than steel or iron, and it weighs about a third of what cast iron blocks do, which means a lot less hand and wrist fatigue during a long casting session. The cavity halves are CNC machined for tight roundness and size control, so most bullets can go straight from the mould to your sizer or even as-cast. Aluminum is softer than blued steel, so a gentle break-in and careful handling will keep this mould dropping good bullets for years.

Getting the Most From Your Wadcutter Pistol Mould

New aluminum moulds like this one benefit from a quick break-in. A clean cavity, a light smoke from a candle on the cavity faces and the underside of the sprue plate, and a few warm-up casts will have it filling out crisp, square-shouldered wadcutters in no time. Handles and the sprue plate are included, so you've got what you need to start casting once your pot is up to temperature.

Key Specifications

  • Manufacturer: Lee Precision
  • Manufacturer Part Number: 90312
  • UPC: 734307903121
  • Bullet Diameter: .358 inch
  • Bullet Weight: 148 Grain
  • Bullet Style: Wadcutter (WC)
  • Cavities: 2 (Double Cavity)
  • Block Material: Aluminum
  • Compatible Cartridges: .38 Special, .357 Magnum, .38 S&W, .38 Colt New Police
  • Bullet Overall Length: .577 inch
  • Crimp Groove to Nose: .105 inch
  • Ballistic Coefficient: .072
  • Country of Origin: United States

What’s Included

  • Lee 358-148-WC double cavity mould block
  • Mould handles
  • Sprue plate

Frequently Asked Questions

What cartridges can I load with bullets from the Lee 358-148-WC mould?

This mould drops .358 diameter 148 grain wadcutters that work in .38 Special, .357 Magnum, .38 S&W, and .38 Colt New Police. The 148 grain wadcutter is a classic choice for .38 Special target and bullseye loads. For .357 Magnum you can seat them a little deeper, though most folks run these in .38 Special for light, accurate practice ammo.

Does the Lee wadcutter mould come with handles?

Yes. The handles and sprue plate are included in the box, so you can start casting as soon as your alloy is up to temperature. Just remember the handles pair to the mould block and are what you'll use to open and close it during each pour.

Why is this mould made from aluminum instead of steel?

Aluminum won't rust, it heats and cools faster than iron or steel, and the blocks weigh about a third as much, which reduces hand fatigue during long casting sessions. The tradeoff is that aluminum is softer than blued steel, so it rewards gentle handling. Treat it with a little care and it will drop good bullets for a very long time.

Do I need to do anything before casting with a new Lee mould?

A quick break-in helps a new aluminum mould fill out cleanly. Wash the cavity, dry it, and lightly smoke the cavity faces and the underside of the sprue plate with a candle, then run a few warm-up casts to get the block up to temperature. After that, the wadcutters should come out crisp and square-shouldered.

Additional information

UPC

734307903121

Manufacturer

Manufacturer Part Number

90312

Bullet Weight (Grains)

148

Caliber/Gauge

.38 Caliber

Shipping Weight

0.8875

Reviews

There are no reviews yet.

Be the first to review “Lee 358-148-WC Double Cavity Wadcutter Bullet Mould .358 148 gr”