Description
Casting your own .401 diameter 145-grain semi-wadcutter bullets is one of the easiest ways to keep your 40 S&W or 10mm Auto fed without burning through a budget. This Lee 401-145-SWC double cavity mold does exactly that, dropping two bullets per pour from a lightweight aluminum block that heats up quickly and gets you to good castings in just a few pours. The semi-wadcutter profile cuts a clean hole in paper, which is why it's such a favorite for target work and plinking, and the flat shoulder feeds well in most pistols chambered for .401 diameter rounds.
What Sets the Lee 401-145-SWC Mold Apart
Lee machines their mold blocks from aluminum, which is the real story here. Aluminum heats and cools faster than iron or steel, so you spend less time waiting for the mold to come up to temperature and more time casting. The blocks are also roughly a third the weight of steel, which cuts down on hand fatigue during long sessions at the pot. The cavities are CNC machined for tight roundness and consistent sizing, and the hard anodized sprue plate features a tangential cut off that helps eliminate the little nib left at the sprue.
Specs on the 401-145-SWC Semi-Wadcutter
This mold produces a bullet with an overall length of .530 inches and a ballistic coefficient of .117, measured from the nose to the first lube groove at .220 inches. Bullet weight runs around 145 grains with Lee's suggested alloy, though your actual weight will shift a little depending on the lead mix you run. Hardwood handles are included in the box, so there's nothing extra to buy to start casting.
Getting Good Bullets From Your Lee Mold
A quick tip from folks who cast with these regularly: preheat the mold before you start, either by setting it near the pot or dipping a corner into the molten alloy for about half a minute. Lee recommends smoking the cavities with a wooden match, beeswax candle, or butane lighter rather than using spray release products, which can build up and shrink your bullet diameter over time. Keep the alloy hot and cut the sprue while it's still soft, and you'll be dropping clean, uniform bullets in short order.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90470
- Model: 401-145-SWC
- UPC: 734307904708
- Projectile Diameter: .401 inch
- Bullet Weight: 145 grain
- Bullet Style: Semi-Wadcutter (SWC)
- Cavities: 2
- Mold Caliber: 40 S&W / 10mm Auto
- Block Material: Aluminum
- Sprue Plate: Hard Anodized
- Handles Included: Yes
- Gas Check: No
- Bullet Overall Length: .530 inch
- Ballistic Coefficient: .117
- Country of Origin: United States
What’s Included
- Lee 401-145-SWC double cavity bullet mold block
- Hardwood mold handles
- Hard anodized sprue plate
- Instruction sheet
Frequently Asked Questions
What cartridges does the Lee 401-145-SWC mold work for?
This mold casts a .401 diameter 145-grain semi-wadcutter bullet, which is sized for cartridges like 40 S&W and 10mm Auto. After casting, you'll want to size and lube the bullets to match your load before seating. It's a solid choice for target shooting and general range use in those calibers.
Does the Lee 401-145-SWC mold come with handles?
Yes, the hardwood handles are included in the box along with the aluminum mold blocks and the hard anodized sprue plate. You won't need to buy handles separately to start casting. Keep in mind the mold does not include any sizing or lube equipment, which is sold separately.
Why are Lee molds made from aluminum instead of steel?
Aluminum conducts heat quickly, so the mold reaches casting temperature faster and you can usually produce good bullets after just a few pours. The blocks are also about a third the weight of iron or steel, which means less hand fatigue during long casting sessions. Aluminum is rust resistant too, which makes storage easier.
How do I get clean bullets from the start with this mold?
Preheat the mold before casting, either by setting it near the pot or dipping a corner into the molten alloy for about 30 seconds. Lee recommends smoking the cavities with a match or butane lighter rather than using spray release products, which can build up and reduce bullet diameter. Keep your alloy hot and cut the sprue while it's still soft for the best results.




Reviews
There are no reviews yet.