Description
If you shoot the old .32 cartridges and you're tired of chasing down pricey factory bullets, this Lee 311-93-1R six-cavity mould puts bullet making right in your own garage. It drops .311" diameter, 93-grain round nose projectiles with a single-radius ogive, and with six cavities working at once you can fill a bullet box in short order. Lee designed these blocks for heavy-duty volume production, so they hold up to long casting sessions without complaint.
What the 311-93-1R Mould Casts
This one is set up for the .32 family, meaning cartridges like .32-20 WCF, .32 S&W Long, and .32 Colt New Police. The finished bullet runs about .509" overall length with a ballistic coefficient near .125, and the distance from the nose to the first lube groove sits around .229". A lot of casters run these bullets as-cast without sizing, though a quick pass through a sizer never hurts if you want them dialed in tight.
Why Casters Like the Aluminum Blocks
Lee machines these blocks from aluminum rather than steel or iron, and that pays off in a few ways. The cavities can't rust, the blocks heat up and cool down fast so you're getting good fillout after just a few pours, and they weigh about a third of what a comparable iron mould does, which your forearm appreciates during a long afternoon at the pot. The cavities are bored for roundness and consistent size, and steel bushings with alignment pins keep the halves registering the same way pour after pour.
Built for the Long Haul
The cam-operated sprue plate is one of the real upgrades here. It's hard anodized, held down with wave washers at each end, and the cam action makes cutting all six sprue easy without hammering on the mould. Take care of it, give the pivots a little oil, and keep the cavities clean, and a mould like this will outlast most of the guns you feed with it. Keep in mind the handles are not included and are sold separately as Lee item 90005.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90308
- Model: 311-93-1R
- UPC: 734307903084
- Number of Cavities: 6
- Bullet Diameter: .311"
- Bullet Weight: 93 grains
- Bullet Style: Round Nose, 1-Ogive Radius
- Suited Cartridges: .32-20 WCF / .32 S&W Long / .32 Colt NP
- Block Material: Aluminum with steel bushings and alignment pins
- Sprue Plate: Hard-anodized, cam-operated
- Bullet Overall Length: .509 inches
- Ballistic Coefficient: .125
- Handles: Sold separately (Lee item 90005)
What’s Included
- Lee 311-93-1R six-cavity mould blocks
- Cam-operated hard-anodized sprue plate
- Molded storage case
Frequently Asked Questions
Does the Lee 311-93-1R mould come with handles?
No, the handles are sold separately. You'll want Lee's six-cavity mould handles, item number 90005, to open and close the blocks. Since one set of handles swaps between any of Lee's six-cavity moulds, a lot of casters pick up a pair and move them from mould to mould.
What cartridges can I load with the 93-grain .311 bullets from this mould?
This mould is built for the .32 family, including .32-20 WCF, .32 S&W Long, and .32 Colt New Police. The .311" diameter and 93-grain round nose shape work well across those classic cartridges. Always check your load data and verify bullet diameter against your firearm's bore before casting in bulk.
Do I need to size the bullets after casting?
Many casters run Lee bullets as-cast without sizing, especially since the cavities are bored for consistent roundness. That said, running them through a sizer die gives you tighter control over final diameter and helps with lubing. It comes down to your rifle or revolver and how fussy you want to be about fit.
Why choose an aluminum mould over a steel or iron one?
Aluminum blocks can't rust in the cavities, they heat up and cool down faster so you get good fillout quickly, and they weigh about a third of a comparable iron mould. That lighter weight cuts down on fatigue during long casting sessions. With a little care and the occasional drop of oil on the pivots, these moulds last for decades.





Reviews
There are no reviews yet.