Description
The Lee Carbide Factory Crimp Die for .30 Super Carry is the die you reach for at the final station of your reloading process. It applies a taper crimp to the case mouth, which is exactly what you want for a cartridge that headspaces on the mouth, and it does it cleanly without buckling the case. What really sets it apart from a plain taper crimp die is the carbide sizing ring down in the base. As the finished round is drawn out of the die, that ring post-sizes the whole cartridge to spec, ironing out any slight bulge from a seated bullet so the round chambers freely with factory-like dependability.
Why the Carbide Ring on This .30 Super Carry Die Matters
That carbide ring is the heart of the Factory Crimp Die. Think of it like a built-in case gauge check on every single round. If a case has a bit of a bulge from a slightly fat bullet or a touch too much crimp, the ring brings it back into line as the cartridge exits. Trim length isn't critical here either, so you skip the case trimming and chamfering step that eats up bench time with other setups. A firm, uniform crimp also helps build consistent start pressure, which translates to a smoother pressure curve and tighter velocity spreads downrange.
Setting Up the .30 Super Carry Factory Crimp Die
Adjustment is about as simple as it gets. Back the knob on top all the way up, thread the die into the press until it touches the raised shellholder, then dial in the crimp with the adjusting screw until it feels right. Once it's set, the die body stays put, so you're just tweaking the knob if you ever need to. For single-stage loaders especially, having a dedicated crimp die means you never have to disturb your seating die to adjust a crimp.
It uses the standard 7/8-14 thread, so it drops right into any common reloading press. If you're loading .30 Super Carry on the regular, this die earns its spot at the end of your lineup.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 91890
- UPC: 734307918903
- Caliber: .30 Super Carry
- Die Type: Carbide Factory Crimp Die
- Crimp Style: Taper Crimp
- Carbide Sizing Ring: Yes, post-sizes finished cartridge
- Thread Size: 7/8-14
- Gun Type: Handgun / Semi-Auto
- Shellholder Included: No
- Country of Origin: USA
- Shipping Weight: 0.355 lbs
What’s Included
- Lee .30 Super Carry Carbide Factory Crimp Die
- Adjusting screw/knob
- Plastic storage container
- Instructions
Frequently Asked Questions
Does the Lee Factory Crimp Die for .30 Super Carry apply a taper or roll crimp?
It applies a taper crimp, which is the correct style for the .30 Super Carry since it headspaces on the case mouth. Taper crimps are standard for rimless semi-auto cartridges because they hold the bullet without rolling the mouth into a groove. The adjusting screw lets you set exactly how much crimp you want.
What does the carbide ring in this die actually do?
The carbide sizing ring in the base of the die post-sizes the entire finished cartridge as you draw it back out. It's ground to the maximum allowable outside diameter for the case, so any slight bulge from a seated bullet or a heavy crimp gets smoothed back into spec. The payoff is that your loaded rounds chamber freely, almost like a built-in case gauge check on every round.
Do I need a shellholder with the .30 Super Carry Factory Crimp Die?
A shellholder is not included with this die, so you'll want to make sure you have the correct one for .30 Super Carry on hand. The die itself uses the standard 7/8-14 thread and will work in any common single-stage or progressive reloading press.
Can this die seat bullets too, or is it crimp only?
This is a crimp-only die, so there's no bullet seating function built in. It's designed to run as a separate last-step die in your process, which is handy because you never have to readjust your seating die to change a crimp. A lot of loaders like splitting seating and crimping into two stations for more consistent results.




Reviews
There are no reviews yet.