Description
The Lee Precision Carbide 3-Die Set in .38 S&W is built for folks keeping that old nine-shooter or top-break revolver fed. This is the classic .38 Smith & Wesson round, also known as .38 Colt New Police, so it's the right tool for a cartridge the big ammo makers rarely stock anymore. The real draw here is the carbide sizing die. Because the carbide ring handles the brass without you needing to lube every case first, you skip a step and the cleanup that comes with it, which speeds up your bench time considerably.
What the Lee .38 S&W Die Set Does on the Press
All three dies thread into any standard 7/8-14 reloading press, so this drops right into whatever single stage or turret setup you already run. The carbide full-length sizing die resizes and deprimes in one stroke, and the dies are contour ground for step-less sizing, meaning you won't see that pronounced ring other brands can leave on a case. The powder-through expanding die flares the case mouth just enough to seat a bullet while letting you drop a charge through it, which pairs nicely with a Lee auto-disk measure or the included dipper. The bullet seating die finishes the job with an adjustable crimp that runs from a light taper to a full roll.
Loading the .38 S&W with the Lee Carbide Dies
One thing worth knowing about this cartridge: the .38 S&W is shorter and fatter than a .38 Special and takes a larger .360 diameter bullet, so this is not the same die set as a .38 Special or .357 Magnum kit. Hollow-base wadcutters and properly sized lead bullets tend to give the best results in these older bores. Seating and crimping happen in the same step with this set, so a little extra care dialing in that die pays off with consistent, accurate loads. For a cartridge you often can't buy off the shelf, rolling your own is really the best way to keep shooting one of these heritage revolvers.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90569
- UPC: 734307905699
- Caliber: .38 S&W (.38 Colt New Police)
- Product Type: Carbide 3-Die Set, Pistol
- Number of Dies: 3
- Die Types: Carbide Full-Length Sizer, Powder-Thru Expander, Bullet Seater
- Die Threads: 7/8-14
- Material: Carbide
- Shell Holder: Included
- Case Lube Required: No
- Crimp Type: Adjustable, slight taper to full roll
- Country of Origin: United States
- Length: 4.9 in
- Shipping Weight: 1.2 lb
What’s Included
- Carbide full-length sizing die with decapping unit
- Powder-thru expanding die
- Bullet seating die
- Universal shell holder
- Powder dipper
- Instructions and load data
- Plastic storage container
Frequently Asked Questions
Do I need case lube with the Lee .38 S&W carbide die set?
No, the carbide sizing die lets you resize cases without lubing them first. The carbide ring does the work on its own, so you skip the lube step and the cleanup afterward. That alone makes reloading faster and a lot less messy on the bench.
Can this die set load .38 Special or .357 Magnum too?
No, this set is specific to the .38 S&W cartridge, which is shorter and fatter than a .38 Special and uses a larger .360 diameter bullet. You'll need a separate die set for .38 Special or .357 Magnum. Match your dies and bullet diameter to the actual cartridge you're loading.
What press does the Lee Carbide 3-Die Set fit?
The dies use standard 7/8-14 threads, so they'll fit just about any single stage, turret, or progressive press from Lee and most other brands. If your press takes common reloading dies, this set drops right in. No special adapters needed.
What bullets work best in .38 S&W with this set?
Properly sized lead bullets around .360 diameter tend to give the best results in these older bores. Hollow-base wadcutters are a popular starting point because the base expands to take up any slack in the bore. Always check a current reloading manual for load data since this cartridge runs at lower pressures than a .38 Special.



Reviews
There are no reviews yet.