Description
Round balls have their place, but if you're shooting a .44 caliber cap-and-ball revolver and want more punch downrange, a conical bullet is where it's at. The Lee 90382 is a double cavity mould that casts .450 diameter round nose conical bullets at a nominal 200 grains, giving you heavier, longer projectiles that carry more energy and group tighter than the round balls most folks start out with.
The double cavity setup means you drop two bullets every pour, so a casting session goes quick. The blocks are machined from aluminum, which heats up and cools down fast and shrugs off rust better than iron or steel. Lee cuts the cavities on CNC equipment for good roundness and dimensional consistency, and most bullets drop ready to load with no sizing needed. The design uses a tangential sprue cutoff to help eliminate the little nip left behind at the cut, and two lube grooves on the bullet help cut down on flash ignition and lead fouling when you're running real black powder.
What the Lee 90382 Mould Casts
These are 450-200-1R bullets, meaning .450 diameter, 200 grain, single ogive radius round nose. They're sized for Colt and Remington style replica .44 revolvers. Keep in mind the 200 grain figure is based on Lee's suggested alloy, so your actual weight will shift a bit depending on the lead mix you run. Pure lead is standard for cap-and-ball work and runs soft so it seats cleanly over the chamber.
Getting the Most From Your Lee Conical Mould
Lee recommends skipping any spray-type mould release, since it can gum up the cavities and hurt your fill-out. A quick smoke of the cavities and keeping the blocks at casting temperature will get you clean, frosty bullets that fall right out. Steel sprue plate and long-lasting hardwood handles come in the box, so you've got what you need to start dropping bullets right away.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90382
- UPC: 734307903824
- Bullet Design: 450-200-1R Round Nose Conical
- Bullet Diameter: .450 in
- Caliber: .44 Caliber Cap-and-Ball
- Bullet Weight: 200 Grain (nominal, varies by alloy)
- Cavities: 2 (Double Cavity)
- Lube Grooves: 2
- Block Material: Machined Aluminum
- Sprue Plate: Steel
- Handles: Hardwood, Included
- Fits: Colt and Remington replica .44 revolvers
What’s Included
- Lee 90382 double cavity bullet mould blocks
- Steel sprue plate
- Hardwood handles
- Instruction sheet
Frequently Asked Questions
What revolvers is the Lee 90382 .450 conical mould made for?
This mould casts .450 diameter 200 grain conical bullets sized for .44 caliber cap-and-ball revolvers. It works with the common Colt and Remington style replica .44 revolvers that black powder shooters use. The conical shape seats over the chamber mouth and gives you more mass than a round ball.
Why choose a conical bullet over a round ball?
A conical bullet carries more mass and length than a round ball of the same caliber, so it delivers more energy and tends to group tighter. The Lee 90382 design also includes two lube grooves that help reduce flash ignition and keep lead fouling in check. Many shooters step up to conicals once they want better downrange performance from their cap-and-ball revolver.
Does the Lee 90382 mould come with handles?
Yes. The mould ships with hardwood handles and a steel sprue plate, plus an instruction sheet, so you're ready to cast out of the box. The blocks themselves are machined aluminum, which heats and cools quickly during a casting session.
Will the bullets really weigh exactly 200 grains?
The 200 grain figure is Lee's nominal weight based on their suggested alloy. Your actual bullet weight will vary a little depending on the lead mix you cast with, since pure lead and harder alloys drop at slightly different weights. Most cap-and-ball shooters run soft or pure lead for these bullets.





Reviews
There are no reviews yet.