Description
The Lee Precision 90016 is a six-cavity mold made for folks who want to crank out a lot of cast bullets without babysitting the pot all afternoon. It drops gas-checked .358 diameter bullets at right around 200 grains in a flat nose design, which makes it a natural fit for the .35 Remington and other .35 caliber loads. With six cavities going at once, you fill the pot, get into a rhythm, and your productivity jumps compared to a two-cavity setup.
What Sets the Lee 90016 Apart
The mold blocks are machined from aluminum, which does a couple of things for you. Aluminum heats up and cools down faster than iron or steel, so you're casting good bullets after just a few throwaway pours while the blocks come up to temperature. It's also about a third the weight of a steel mold, so your hands and wrists aren't wrecked after a long session. The blocks are CNC machined with steel bushings and alignment pins, so the two halves close the same way every time and your bullets stay round and on-size run after run.
Casting With the 90016 Six-Cavity Mold
Up top you get a cam-operated, hard-anodized sprue plate held down by tempered spring washers at each end. That camming action lets you cut the sprue cleanly without hammering on the mold, which is easier on the tool and a lot easier on your hands. Folks who've run these say the finished bullets drop free from the aluminum blocks without any mallet-whacking, and the weight variation between the six cavities stays nice and tight.
Fitting the .35 Remington and Beyond
This bullet design works in pretty much any .35 caliber rifle, but it was laid out with the .35 Remington in mind. That cartridge has a short neck and very little throat, so the bullet carries a shorter body and a longer bearing section at a slightly smaller diameter to ride the bore. One thing to know going in: the handles are not included, so you'll want to grab a set of Lee six-cavity mold handles to run it.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number (MPN): 90016
- UPC: 734307900168
- Bullet Diameter: .358 inch
- Bullet Weight: 200 Grain
- Bullet Style: Flat Nose, Gas-Checked
- Caliber: .35 Remington / .35 Caliber
- Cavities: 6
- Block Material: Aluminum
- Sprue Plate: Cam-operated, hard anodized
- Ballistic Coefficient: 0.186
- Length: 13 in
- Weight: 1.26 lbs
- Handles: Sold separately
What’s Included
- Lee Precision 90016 6-Cavity Bullet Mold (blocks)
- Cam-operated hard-anodized sprue plate (installed)
Frequently Asked Questions
Does the Lee 90016 mold come with handles?
No, the handles are not included with this mold. You'll need to pick up a set of Lee six-cavity mold handles separately to clamp and operate the blocks. Lee uses the same six-cavity handles across its six-cavity mold lineup, so if you already own a set they'll work here.
What cartridges can I load with the bullets this mold casts?
It drops a .358 diameter, 200-grain flat nose bullet that was designed with the .35 Remington in mind, thanks to its shorter body and longer bearing section that suits that cartridge's short neck and minimal throat. The bullet will work in other .35 caliber rifles as well. It's designed to run with a gas check for higher velocity loads.
Why choose an aluminum mold over iron or steel?
Aluminum blocks heat up and cool down faster than iron or steel, so you're casting usable bullets after just a few warm-up pours. They're also roughly a third the weight of a steel mold, which keeps fatigue down during long casting sessions. On top of that, aluminum is rust resistant, so storage is less of a worry.
How many bullets does the Lee 90016 cast per pour?
This is a six-cavity mold, so you get six bullets with every fill. That's a big step up in output over a two-cavity setup, which is why these are built for heavy-duty volume production. Once the blocks are up to temperature and you settle into a rhythm, you can stack up finished bullets fast.





Reviews
There are no reviews yet.